01 COA & batch testing

What the COA for bone collagen peptides actually contains

Technical document 01 · Reviewed 2026-11-19 · Bone Collagen Peptides

On this page
  1. The parameter list
  2. What the protein figure is measured against
  3. Catalogue range, release limit and lot result
  4. What moves between lots
  5. When to send a sample to an outside laboratory
  6. What to compare between suppliers

A certificate for bovine bone collagen peptides carries four figures that decide what the material is: the protein content with its nitrogen factor, the hydroxyproline content, the ash the bone mineral leaves, and the molecular weight distribution. Each figure is only meaningful beside its method. The catalogue specification sets the ranges; the batch COA confirms what the lot in the drum measured.

In one line

A bone collagen certificate is complete only when the protein factor, the hydroxyproline figure, the ash and the peptide distribution appear together, each with its method.

The parameter list

The parameter list follows from what the material is: a spray-dried hydrolysate of bovine bone collagen, specified at ≥90% protein, 8–12% hydroxyproline and a 3,000 Da peptide cut-off. The tables below are the catalogue list with the method beside each line.

Identity and composition · bovine bone collagen peptides
ParameterMethodCatalogue limit
AppearanceVisualWhite to off-white powder
Protein (dry basis)Kjeldahl, N × 5.55≥90.0%
HydroxyprolineHPLC8.0–12.0%
Molecular weightSEC≥90% below 3,000 Da
Loss on dryingGravimetric, 105 °C≤7.0%
AshGravimetric, furnace≤5.0%
pH (5% solution)Potentiometry5.0–7.0
Contaminants and physical parameters · bovine bone collagen peptides
ParameterMethodCatalogue limit
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

The tissue is also a parameter, though it produces no number: bone and hide are different raw materials with different ash profiles and label declarations. The source comparison covers that choice.

What the protein figure is measured against

Kjeldahl measures nitrogen, not protein. The nitrogen result becomes a protein figure only after a conversion factor is applied, and collagen uses 5.55 rather than the 6.25 applied to a general food protein. The factors are about 12% apart: 90.0% under 5.55 reads close to 101% under 6.25, the same powder with a different convention.

Bone material adds a second basis. Protein is on a dry basis while ash and moisture are as-is. At the 7.0% moisture limit, 90.0% dry-basis protein is about 83.7% as-is; with 5.0% ash, roughly 4% remains for fat and carbohydrate — a normal mass balance, and the reason ash is not a purity figure on its own.

Ash also separates this grade from hide collagen, usually specified at ≤2.0%: a bone hydrolysate carries more mineral unless demineralisation removes it.

Catalogue range, release limit and lot result

A release limit is the window a lot must fall inside; a lot result is what the laboratory measured. A useful certificate shows both, with the method beside each line, because “conforms to specification” is a conclusion without evidence.

The molecular weight line is often compressed into a single number. The specification asks for ≥90% of the mass below 3,000 Da, a gate rather than a description: two lots can both pass while one sits near the cut-off and the other well below it. Ask for the distribution, not only the pass mark.

Hydroxyproline has a smaller version of the same problem. The catalogue specifies HPLC; a colorimetric result is not the same measurement and should not be compared line for line with an HPLC figure, even when both land inside 8–12%.

This is a catalogue specification: it states what the material is expected to meet, while the batch COA confirms the lot that ships. No page on this site reports a batch result, a batch number or a customer.

What moves between lots

Ash is the parameter most exposed to the raw material: bone from different animals, skeletal sites and rendering plants carries different mineral loads, and demineralisation does not always remove it to the same end point. A supplier drawing from several plants should be able to name the plant behind the lot.

Protein and hydroxyproline move together and usually stay inside a narrow band once hydrolysis is fixed. The molecular weight distribution moves with hydrolysis time, temperature and the filtration that follows, and it is the parameter most likely to drift when equipment changes. Moisture follows the dryer; colour follows both raw material and dryer.

Odour is the least quantitative signal and often the most useful. A faint broth note strengthens with moisture and storage temperature, and the protein figure can still pass while the odour no longer suits a flavoured stick. Ask for the retained sample and the storage history.

When to send a sample to an outside laboratory

Order an independent test when the source is new, when the first commercial shipment enters a regulated market, or when the label makes a statement the certificate does not prove. The useful panel answers the open question: hydroxyproline and the amino acid profile for identity, SEC for the distribution, ash and ICP-MS for the mineral and contaminant load, and species PCR where the tissue declaration is in doubt.

The TSE file is not a laboratory test. It is a document and audit question, answered by slaughterhouse controls, the processing record and the declaration that travels with the lot. The quality page describes how the batch file and the retained sample are kept together.

What to compare between suppliers

Put six lines side by side before looking at anything else: the protein figure with its nitrogen factor and basis, the hydroxyproline figure with its method, the molecular weight distribution with its method, the ash limit, the species and tissue, and the BSE/TSE declaration. If two quotations agree on the protein percentage and disagree on the other five, they are not quoting the same material.

The second layer is the record behind the certificate: which site made the lot, which raw material batch went in, which hydrolysis and drying conditions were applied, and what retained sample exists. A certificate can be accurate and still describe a lot other than the one that arrives. The lot number on the COA, on the drum and on the retained sample should be the same number.

For the ranges themselves, see the bone collagen peptides product page. The source decision is on the bone versus hide page, the tests that prove identity are on the identity page, and the definition of the certificate is in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation