02 Grade comparison

Bone or hide collagen peptides: choosing a source

Technical document 02 · Reviewed 2026-11-19 · Bone Collagen Peptides

On this page
  1. Why one species covers two materials
  2. The two sources side by side
  3. What changes in the drum
  4. What changes in the finished product
  5. What to put in the specification
  6. When the source question is not worth reopening

Bone and hide collagen peptides are both bovine collagen hydrolysates, and both can be specified at ≥90% protein. What reaches the customer is different: the ash the bone mineral leaves, the peptide curve the raw material can hold, the TSE file that follows the tissue, and the words on the label. Choosing a source is a specification decision before it is a sensory one.

In one line

Bone and hide collagen come from the same animal but not the same tissue; the choice turns on ash, the peptide curve, the TSE file and the label wording.

Why one species covers two materials

A collagen peptide grade is usually described by species, and that description hides the tissue. Bovine collagen can come from hide, from bone, or from a mix of both, and the three are not the same purchase. Hide is the dermis, a dense collagen network with little mineral. Bone is a composite of collagen and hydroxyapatite, and that mineral has to be removed before or during hydrolysis if the ash figure is to stay low. The hydrolysis step is similar; the raw material and the clean-up are not.

The difference is not cosmetic. It changes the ash limit, the TSE document that has to travel with the lot, and the ingredient name on the finished pack. A buyer who compares only the protein percentage will see two quotations that look identical and receive two different materials.

The two sources side by side

Bovine bone versus bovine hide collagen peptides · catalogue comparison
PointBoneHide
Raw materialBovine bone, mineralisedBovine hide split, dermis
Ash limit≤5.0% in this catalogueUsually ≤2.0%; agree in the specification
Protein≥90.0% (Kjeldahl, N × 5.55)Same range commonly specified
Hydroxyproline8.0–12.0% (HPLC)Similar range, confirm by HPLC
Mineral removalDemineralisation before hydrolysisNo mineral removal step
Peptide curveSet by hydrolysis; confirm by SECSet by hydrolysis; confirm by SEC
OdourFaint broth note possibleUsually more neutral
TSE fileTissue-specific; bone is the focusHide declaration; lower-risk tissue

Read the table down the ash and TSE columns first. Those two decide whether the material can enter the formula and the market at all; the rest is optimisation.

What changes in the drum

Ash is the first physical difference. At the 5.0% limit, a 25 kg drum carries more than a kilogram of mineral material that is not protein. Two lots at the same protein figure can differ by three percentage points of ash, which is 30 g per kilogram of powder. In a 1 g capsule fill that is 30 mg of the fill weight doing something other than delivering peptide.

Particle size and flow follow the drying route more than the tissue. The catalogue standard is ≥95% through 40 mesh, with agglomerated and low-dust granulated forms available on request. A bone hydrolysate that has been demineralised and spray-dried usually behaves like a hide hydrolysate of the same mesh; the difference is in the colour and the odour, not in the flow.

What changes in the finished product

In a capsule, ash takes up space in the fill and appears in the mass balance of the label. A formulator working to a fixed capsule size has to decide whether the ash is acceptable or whether a hide grade at ≤2.0% makes the fill easier to close. In a powder stick, the ash matters less than the odour and the colour, because the powder is tasted and seen.

In a clear beverage, the peptide distribution matters more than the source. Both tissues can be cut to the same SEC profile, and haze follows the fraction above the cut-off rather than the animal. A bone grade that only just meets the 3,000 Da gate can leave more haze than a hide grade that sits well below it. The comparison should be made on the distribution, not on the tissue word.

In a tablet, the 40 mesh powder and the granulated option decide compressibility and dust. The ash is part of the compression mix and counts toward the tablet weight, so a switch of source is also a re-validation of the tableting run.

What to put in the specification

The specification should open with the tissue, not only the species: “bovine bone collagen peptides, spray-dried” is a different line from “bovine collagen peptides”. After that, the six figures that make the material reproducible:

  • Protein ≥90.0% by Kjeldahl with the N × 5.55 factor, on a dry basis.
  • Hydroxyproline 8.0–12.0% by HPLC.
  • Molecular weight ≥90% below 3,000 Da by SEC, with the distribution reported.
  • Ash ≤5.0%, with the demineralisation step described.
  • Loss on drying ≤7.0%, pH 5.0–7.0 in 5% solution, ≥95% through 40 mesh.
  • Species, tissue, country of origin, BSE/TSE declaration and allergen statement.

The COA page sets out how each of those lines is read, and the bone versus hide page takes the ash and TSE comparison further.

When the source question is not worth reopening

If the finished label already says bovine collagen and the specification has no tissue line, a switch to bone is a specification change, not a like-for-like substitution. It needs a new COA, a new TSE declaration, a sensory check and, in most markets, a label review. That work is justified when the bone source is part of the product story, when the ash limit fits the fill, or when the existing supplier cannot provide the TSE file the market asks for.

It is not justified when the only difference is the word on the drum and the customer has no preference. In that case the cheaper decision is to keep the qualified source and spend the effort on the peptide distribution and the contaminant file instead. Whatever the choice, the product page carries the catalogue ranges, and the compliance page sets out what each market expects the file to show.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation