02.1 Bone vs hide

Bone vs hide collagen: ash, profile and the label

Technical document 02.1 · Reviewed 2026-11-19 · Bone Collagen Peptides

On this page
  1. One species, two tissues
  2. Ash: the first number that separates them
  3. The peptide profile
  4. BSE and TSE: the file each tissue needs
  5. What the label can say
  6. When to choose each

Bone and hide collagen peptides are both type I collagen hydrolysates from cattle, and both can be sold as bovine collagen peptides. The tissue is what separates them: bone is mineralised and leaves ash, hide is the collagen-rich dermis that leaves little, and the two carry different TSE declarations and different label statements. They are not interchangeable on a specification or on a pack.

In one line

Bone collagen carries the mineral ash and the tissue-specific TSE question; hide collagen carries a lower ash and a different tissue declaration.

One species, two tissues

Bovine type I collagen is the main structural protein of both hide and bone, and the amino acid profile of the two raw materials is close. That is why a single product name, bovine collagen peptides, can cover both. The difference is in what the tissue brings with it. Hide is almost pure collagen and water. Bone is a composite in which collagen fibres are mineralised with hydroxyapatite, and the mineral has to be removed before the material can meet a low ash figure.

The hydrolysis step is broadly the same in both cases: the collagen is denatured and cut into peptides, then filtered and dried. What differs is the front end of the process, the ash that survives it, and the paperwork that has to accompany a bone lot.

Ash: the first number that separates them

Ash is the mineral residue left after the organic matter is burned off. The catalogue for bone collagen peptides allows up to 5.0%; a hide grade is usually specified at ≤2.0%. The gap is not a quality difference. It is the residue of a mineralised raw material, and it is the fastest way to tell the two declarations apart on paper.

At 5.0% ash, a kilogram of powder carries up to 50 g of mineral material. In a 1 g capsule that is 50 mg of the fill; in a 25 kg drum it is more than a kilogram that is not protein. The figure belongs in the mass balance beside protein, moisture and the remaining fat and carbohydrate, because a specification that fixes protein and moisture but leaves ash open can still deliver a powder that does not add up.

Ash does not prove the tissue. A hide lot blended with bone mineral can show a bone-like figure, and a well-demineralised bone lot can sit in the hide range. Read the ash line with the tissue declaration, not instead of it.

The peptide profile

The peptide distribution is set by the hydrolysis and the filtration, not by the tissue. A bone grade and a hide grade from the same plant can be cut to the same SEC curve, and a buyer comparing two certificates should compare the curves rather than the raw material. The catalogue gate is ≥90% of the mass below 3,000 Da, and the distribution behind that gate is what shows in clarity, dissolution and mouthfeel.

Where the tissue does show is at the edges. Bone needs a demineralisation step before hydrolysis, and that step can remove some of the fine fraction along with the mineral; hide does not have that step. The result is not a rule about which source is finer, only a reason to ask for the curve on the lot. Odour follows the same logic: a bone hydrolysate can carry a faint broth note, a hide hydrolysate is usually more neutral, and neither is visible in the protein figure.

BSE and TSE: the file each tissue needs

The TSE Regulation (EC) No 999/2001 controls the raw material, the specified risk material and the processing conditions for bovine material in the EU, as of this review; the UK retains equivalent controls. Bone is the tissue those rules were written around, so a bone lot draws a longer file: the age and origin of the animals, the slaughterhouse controls that removed the specified risk material, the processing conditions and the site. The declaration has to be issued for the lot, not for the supplier in general.

Hide is not on the specified risk material list, but a hide lot still needs a species and origin statement and a declaration that the animals were fit for human consumption. The file is shorter, not absent. A buyer who is comparing two quotations should compare the two declarations line by line, because a hide quotation that includes a full TSE declaration is not the same offer as one that does not.

What the label can say

“Bovine bone collagen peptides” names the species and the tissue. “Bovine collagen peptides” names the species and leaves the tissue open, and “hydrolysed collagen” names neither. All three can be truthful, but only the first is consistent with a pack that talks about bone, and only the first is consistent with a specification that says bone. If the pack says bone, the specification, the COA and the TSE declaration have to say bone as well.

Bovine collagen is not a declared allergen in the EU or the US, so the allergen statement is short. The species statement still matters for religious and consumer positioning, and the tissue statement matters for any market that asks for a TSE file. The compliance page sets out the full document pack.

When to choose each

Choose bone when the label is built on the bone source, when an ash figure up to 5.0% fits the capsule or the stick, and when the supplier can issue a complete TSE declaration for the lot. Choose hide when the formula is ash-sensitive, such as a high-dose clear beverage, when a lower ash makes the mass balance easier to close, or when a more neutral odour matters more than the source story.

The protein figure does not decide it: both sources can be specified at ≥90%. The decision is the ash limit, the peptide curve, the declaration and the label word, in that order. The grade comparison puts the two beside each other across the full specification, the identity page covers the tests behind the tissue claim, and the product page carries the catalogue ranges.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation