06 Identity & adulteration

Proving a zinc sulfate lot is the heptahydrate

Technical document 06 · Reviewed 2026-11-19 · Zinc Sulfate

On this page
  1. Identity evidence, layer by layer
  2. The zinc, sulfate and water ratio
  3. IR and X-ray diffraction: the solid-state check
  4. What substitution looks like
  5. Identity lines for the specification
  6. Five questions before approval

A zinc sulfate lot is the heptahydrate when the document names the hydrate and CAS number, complexometric titration gives 22.0–23.0% zinc, Karl Fischer gives 43.0–46.0% water, the sulfate figure closes the mass balance, and IR or X-ray diffraction matches the heptahydrate reference. The assay alone cannot separate the hydrates or a dilution. Identity is the set of figures agreeing, not one percentage on its own.

In one line

Identity is the zinc figure, the sulfate figure and the water figure agreeing on the same hydrate, not the assay percentage on its own.

Identity evidence, layer by layer

A certificate can carry the right name and still not demonstrate it. Each layer is a separate question with its own evidence. An answer that stops at the first question describes paperwork, not powder.

Identity evidence for zinc sulfate heptahydrate
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
ZincIs the zinc figure right?Complexometric titration (EDTA)The zinc content, not the hydrate
WaterIs it the heptahydrate?Karl FischerThe hydration state
SulfateIs the anion sulfate?Ion chromatography or gravimetric sulfateThe salt, and the mass balance
Solid stateIs the crystal the heptahydrate?IR, and XRD for a disputeThe hydrate as a solid

The catalog identity is “IR and titration conform”. That is a reasonable release gate, but it does not report the water or the sulfate as numbers. When the hydrate is disputed, ask for the Karl Fischer result, the sulfate result and the diffraction pattern; a conformity statement is not a measurement.

The zinc, sulfate and water ratio

The formula fixes the mass balance. In 100 g of pure ZnSO4·7H2O there are 22.74 g of zinc, 33.41 g of sulfate and 43.86 g of water. The zinc-to-sulfate mass ratio is 22.74 ÷ 33.41 = 0.681, and the molar ratio is 1:1. The zinc figure and the assay expressed as heptahydrate are related by 287.55 ÷ 65.38 = 4.398, so 22.5% zinc is 98.9% heptahydrate and 100.5% assay is 22.85% zinc.

Read the three figures together and the hydrate identifies itself. Zinc high with water low points to the monohydrate or the anhydrous salt; zinc low with water normal points to a dilution or a different zinc salt; water high with zinc low points to surface moisture. A lot with 23.0% zinc and 44.0% water is not a pure heptahydrate: the zinc figure is above the stoichiometric 22.74%, so either the method reads high or another zinc species is present.

A blend of hydrates is caught by the same ratio. A powder made from heptahydrate and monohydrate can be formulated to land inside the assay range, but its water figure falls in proportion to the dried fraction. The assay sees the zinc; the water sees the hydrate. That is why the water line belongs on the certificate even though it looks like an impurity line.

IR and X-ray diffraction: the solid-state check

IR is the routine identity test because it is fast and it sees both the sulfate and the water bands. It can separate the heptahydrate from the monohydrate when the spectra are compared with a reference, but the difference is subtle and a library match is only as good as the library. The release identity should name the reference material and the band region used.

X-ray diffraction answers the question more directly: does the solid give the heptahydrate pattern? The three hydrates have different unit cells, so the peak positions differ, and a mixture shows both sets of peaks. XRD is not a purity assay and it does not measure the water content, but it is the strongest evidence that the crystal in the drum is the hydrate named on the certificate.

A “match” claim needs the reference pattern and a stated detection limit in the report. A report that says only “XRD conforms”, without the pattern or the reference, has added little. XRD is the test to order when a supplier's hydrate claim is disputed or when two sources are being compared for a specification change.

What substitution looks like

Substitutions and the signals on a zinc sulfate certificate
SubstitutionWhat it changesSignalTest
Monohydrate sold as heptahydrateZinc per gram up; water downZn above 23.0%; water below 43.0%Karl Fischer, XRD
Sodium sulfate dilutionZinc down; sodium upZn low; sodium present; assay lowICP-OES, mass balance
Magnesium sulfateZinc down; magnesium upZn low; Mg present; different crystalICP-OES, XRD
Zinc oxide blendInsoluble zinc; sulfate downTurbid solution; sulfate below 33%Solubility, sulfate, XRD
Technical gradeHeavy metals upPb, Cd or As above the agreed limitICP-MS
Surface moistureWater up; zinc per gram downWater above 46.0%; cakingKarl Fischer, sieve

Zinc sulfate is a commodity salt, so the common problems are grade and hydrate rather than an elaborate fake. A technical grade that passes the zinc assay can still fail the heavy-metal panel, and a dried lot can pass the assay while failing the water line. Colour is a weak signal on its own: a white powder can be any of the three hydrates, and a yellow tint points to iron rather than to a different zinc salt.

Identity lines for the specification

  • “Zinc sulfate heptahydrate, CAS 7446-20-0, ZnSO4·7H2O.”
  • “Assay 99.0–101.0% as heptahydrate by complexometric titration; state the basis.”
  • “Zinc 22.0–23.0%; water 43.0–46.0% by Karl Fischer.”
  • “Sulfate by ion chromatography or gravimetric method; report the result.”
  • “Identification by IR against a named reference; XRD on request.”
  • “Heavy metals by ICP-MS, individual elements; microbiology as listed.”
  • “No substitution of hydrate or grade without written change control.”

Five questions before approval

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. What are the zinc and water results, and what methods produced them?
  3. What is the sulfate result, and does the mass balance close to 100%?
  4. Can you provide the IR spectrum and, if the hydrate is disputed, the XRD pattern with its reference?
  5. Would you agree to a joint re-test of the retention sample if the lot is challenged?

Five direct answers amount to an identity file; a single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the hydrates; the analytical methods library explains the titration, water and diffraction methods; the quality page describes the release and re-test route.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation