Zinc sulfate heptahydrate vs dried: the zinc figure and the fill weight
Dried zinc sulfate, normally the monohydrate, carries about 36.4% elemental zinc; the heptahydrate carries 22.7%. To deliver the same zinc, the heptahydrate needs about 1.6 times the mass, so a switch between the two changes the fill weight, the excipient load and the label arithmetic. The zinc figure, not the salt weight, is the number the label declares.
Dried zinc sulfate carries about 36% zinc against 22.7% in the heptahydrate, so the same fill weight delivers roughly 60% more elemental zinc.
What “dried” means on a zinc sulfate order
“Dried zinc sulfate” is a process name, not a formula. It usually means the monohydrate, ZnSO4·H2O, CAS 7446-19-7, made by removing six of the seven water molecules from the heptahydrate. Some suppliers use the same words for a product closer to the anhydrous salt, and a few sell blends. The certificate's water result is the only reliable statement of which hydrate is in the drum.
The difference is water, not purity. Both grades are zinc sulfate, both dissolve freely and both give an acidic solution. The heptahydrate carries 43.9% water by theory; the monohydrate carries 10.0%; the anhydrous salt carries none. Everything that follows — the zinc per gram, the fill weight, the flow, the caking risk — comes from that one number.
| Property | Heptahydrate | Dried (monohydrate) |
|---|---|---|
| Formula and CAS | ZnSO4·7H2O · 7446-20-0 | ZnSO4·H2O · 7446-19-7 |
| Molecular weight | 287.55 | 179.46 |
| Zinc content | 22.7% theoretical | 36.4% theoretical |
| Water content | 43.9% theoretical | 10.0% theoretical |
| Zinc per 100 g | 22.7 g | 36.4 g |
| Appearance | Colourless crystals or white powder | White powder |
The zinc figure per gram
The conversion is fixed by the formula. For the heptahydrate, 1 g of zinc is 4.40 g of salt; for the monohydrate it is 2.75 g; for the anhydrous salt it is 2.47 g. Read the other way, 100 g of heptahydrate delivers 22.7 g of zinc, 100 g of monohydrate delivers 36.4 g, and 100 g of anhydrous salt delivers 40.5 g. The ratio between the two supplement grades is 36.4 ÷ 22.7 = 1.60.
That ratio is the whole comparison. A 25 kg drum of heptahydrate contains about 5.7 kg of zinc; the same drum of monohydrate contains about 9.1 kg. The dried grade is not a better material, but it is a more concentrated one, and freight, storage and fill weight all follow the concentration rather than the net weight on the label.
The fill weight and the capsule
Work the arithmetic on a label that declares 10 mg of zinc. As heptahydrate it needs 10 ÷ 0.2274 = 44.0 mg of salt; as monohydrate it needs 10 ÷ 0.3643 = 27.5 mg. At 15 mg of zinc the weights are 66.0 mg and 41.2 mg. The difference is 16.5 mg at the 10 mg label and 24.8 mg at the 15 mg label, which is the space the formulator gains or loses in the capsule.
The dangerous case is a switch without the arithmetic. Keep the 44.0 mg fill and use the monohydrate, and the same capsule now delivers 44.0 × 0.3643 = 16.0 mg of zinc against a 10 mg label — about 60% more than declared. Correct the fill to 27.5 mg and the capsule may be too small to handle, or the blend may need more excipient to reach a workable weight. Either way the change belongs in the specification, not at the balance.
Low-dose blends have a second problem: 27.5 mg of salt in a 500 mg capsule is a small fraction of the fill, so blend uniformity and the choice of carrier matter more than they do at 44.0 mg. A direct-compression tablet built on the dried grade also takes a different weight and a different hardness target.
What the label declares
The label declares elemental zinc, not the hydrate. In the EU the ingredient list names the source as “zinc sulphate”, and the nutrition declaration gives the zinc mass and the percentage of the nutrient reference value, which is 10 mg per day. In the United States the Supplement Facts panel reads “Zinc (as zinc sulfate)” with the elemental mass and the percentage of the 11 mg daily value. Neither label has to spell out the hydrate, but the specification and the COA should.
That split is the source of most confusion. A label that says 10 mg of zinc is satisfied by 44.0 mg of heptahydrate or 27.5 mg of monohydrate; the label is right in both cases and the capsules are different. The hydrate belongs in the purchase specification, the certificate and the change-control record, while the label carries the zinc figure the consumer reads.
The label also carries the destination's rules. Zinc has a tolerable upper intake level in the markets that set one, and the finished-product dose is checked against it by the brand's regulatory team. The salt weight is a manufacturing number; the zinc mass is the number that is regulated.
What to recheck when you switch
A change from heptahydrate to dried, or back, is a change of material and should be handled as one. Recalculate the fill weight from the certificate's zinc result, not from the theoretical figure alone. Recheck the blend flow, the tablet weight and hardness, the capsule fill, and the water result of the finished blend. Re-run the stability work if the pack or the moisture environment changes.
Update the specification, the bill of materials, the label artwork if the zinc mass moves, and the supplier's change-control record. Keep a retained sample of both grades so that a disputed fill can be traced. A 1:1 swap by mass is the error to avoid: it is a 60% increase in zinc, not a neutral substitution.
How to write the choice into the specification
- “Zinc sulfate heptahydrate, CAS 7446-20-0, Zn 22.0–23.0%, water 43.0–46.0%.”
- “Dried zinc sulfate monohydrate, CAS 7446-19-7, Zn 35.5–36.5%, water 9.0–12.0%.”
- “Assay by complexometric titration; state the basis and report the zinc result.”
- “Fill weight calculated from the certificate's zinc result, not from the theoretical figure.”
- “Particle size ≥95% through 40 mesh; heavy metals and microbiology as listed.”
- “No substitution of hydrate without written change control and a label check.”
The zinc sulfate product page carries the catalog heptahydrate specification; the grades page places this comparison in the wider range; the zinc oxide page and the zinc citrate page show how different zinc sources compare on the same elemental basis; the quality page describes the release file and the change-control route.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation