Zinc sulfate grades: heptahydrate, dried and anhydrous
Zinc sulfate is supplied as the heptahydrate (ZnSO4·7H2O), the dried monohydrate (ZnSO4·H2O) and the anhydrous salt (ZnSO4), carrying 22.7%, 36.4% and 40.5% zinc. The grade changes the zinc per gram, the water load and the fill weight before it changes anything else. A purchase order that says only “zinc sulfate” has not fixed the grade, the zinc figure or the dose.
The grade is a hydrate decision: heptahydrate, dried monohydrate and anhydrous salt carry 22.7%, 36.4% and 40.5% zinc, so the same weight is not the same dose.
Three hydrates of one salt
Zinc sulfate crystallises from water with seven molecules of water per zinc. Drying removes six of them and leaves the monohydrate; further heating removes the last. The commercial names follow the process rather than the formula: heptahydrate, dried, anhydrous. “Dried” is a process word, so the water content on the certificate is the only reliable statement of which hydrate is in the drum.
The three solids are the same salt at different levels of hydration, not three purities. A dried grade is not “stronger” in the sense of being cleaner; it simply carries more zinc per gram because it carries less water. That distinction matters at the balance, where the formulator weighs a salt, and at the label, where the dose is elemental zinc.
Commercial “dried zinc sulfate” is usually the monohydrate at about 35.0–36.5% zinc. An anhydrous grade is also traded, and some suppliers use “dried” for a product closer to anhydrous. The specification should name the hydrate and give a water range, or the buyer is comparing two different powders under one word.
Three hydrates compared
| Property | Heptahydrate | Dried monohydrate | Anhydrous |
|---|---|---|---|
| Formula | ZnSO4·7H2O | ZnSO4·H2O | ZnSO4 |
| CAS number | 7446-20-0 | 7446-19-7 | 7733-02-0 |
| Molecular weight | 287.55 | 179.46 | 161.44 |
| Zinc content | 22.7% theoretical | 36.4% theoretical | 40.5% theoretical |
| Water content | 43.9% theoretical | 10.0% theoretical | None |
| Appearance | Colourless crystals or white powder | White powder | White powder |
| Water solubility | Freely soluble; acidic solution | Freely soluble; acidic solution | Freely soluble; acidic solution |
| Typical supplement use | Capsules, tablets, powder blends | Dry blends, tablets, low-moisture mixes | Low-moisture systems and specialist uses |
The last row is the practical split. A capsule or a tablet can take any of the three, but the fill weight changes. A dry blend with a moisture-sensitive active should not be built on the heptahydrate unless the water is accounted for. An aqueous system dissolves all three and the choice comes down to the zinc figure and the label.
Crystals, powder, water and flow
The heptahydrate is efflorescent: in dry air it loses crystal water, and the surface of a crystal can turn to a lower hydrate while the core stays heptahydrate. In humid air it can take up surface moisture instead. Both directions change the water result, the zinc per gram and the flow, which is why the packs need a moisture barrier rather than a plain bag.
The catalog form is a 40 mesh powder, with crystals available on request. Crystal size changes the dissolution rate and the dust, not the chemistry. A coarse crystal dissolves more slowly; a fine powder disperses faster but dusts and cakes more readily. A change of particle size is a change of the material as the customer receives it.
The acidity is a formulation fact: it affects the taste of a drink mix, the compatibility with carbonate salts and the corrosion of mild steel. The dried forms carry less water into a blend, but they are still soluble salts and still need a sealed pack.
Zinc arithmetic and the label
The label declares elemental zinc, so the weigh-up has to convert from zinc to salt. At the theoretical figures, 10 mg of zinc needs 44.0 mg of heptahydrate, 27.5 mg of monohydrate or 24.7 mg of anhydrous salt. At 15 mg of zinc the weights are 66.0 mg, 41.2 mg and 37.0 mg. These are arithmetic examples, not a suggested intake.
Two label anchors are useful for the same calculation. In the EU the reference intake for zinc is 10 mg per day, so a product supplying 10 mg carries 100% of the nutrient reference value; in the United States the daily value used on the Supplement Facts panel is 11 mg. The finished-product dose is checked against the destination's upper limit, and the check uses elemental zinc.
The salt weight also sets the dosage form. A 44 mg heptahydrate load fits a small capsule with little excipient; the same zinc as monohydrate is 27.5 mg and may leave room for a second ingredient or allow a smaller tablet. The reverse is also true: a formulator who keeps the heptahydrate fill weight and switches to the monohydrate delivers about 60% more zinc without changing the label. That is a formulation error, not a stronger product.
Specification lines for the hydrate
- “Zinc sulfate heptahydrate, CAS 7446-20-0, ZnSO4·7H2O.”
- “Assay 99.0–101.0% as heptahydrate by complexometric titration; state the basis.”
- “Zinc 22.0–23.0%; water 43.0–46.0% by Karl Fischer.”
- “Appearance: colourless crystals or white powder; particle size ≥95% through 40 mesh.”
- “Heavy metals and microbiology as listed; individual element results on the COA.”
- “For a dried grade: zinc 35.5–36.5% and water 9.0–12.0%, with the hydrate named.”
- “Destination market and intended dosage form confirmed before the order.”
Our standard grade is the heptahydrate. The dried monohydrate and the anhydrous salt are different specifications with different zinc figures, and neither is a drop-in at the same weight. Change the hydrate only through change control, with the fill weight and label recalculated.
When another grade is a mistake
Do not switch to a dried grade to “save space” without recalculating the label. The zinc per gram rises, the fill weight falls and the tablet or capsule may miss its target weight or blend uniformity. Do not keep the heptahydrate in a moisture-sensitive blend without accounting for its crystal water either; the water can cake the blend or move into a hygroscopic active.
The reverse applies too. A specification written around the heptahydrate, with its water range and crystal form, is not met by a dried lot even when the zinc figure is higher. The form is part of the identity, and a change of hydrate is a change of material.
The product hub holds the catalog data for the heptahydrate. The level-four comparison takes the fill-weight arithmetic further; the COA page shows how the hydrate is reported; the zinc oxide page and the zinc citrate page show the other zinc sources, where the zinc figure per gram is different again; the analytical methods library covers the titration and water methods.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation