What the COA for zinc malate actually contains
For a zinc malate lot, the certificate reports appearance, identification by infrared and HPLC, assay by HPLC, zinc by complexometric titration, loss on drying, the heavy-metal panel, microbiology and particle size. The ranges below are the catalog specification; the batch COA is the document that confirms a named pack. Two numbers matter most and they answer different questions: the assay says how much zinc malate is present, and the zinc figure says how much of the element the powder delivers.
A zinc malate certificate carries two numbers — the salt assay and the elemental zinc — and the ratio between them shows whether the two results describe the same powder.
The certificate as a test report
A certificate is only auditable if every line names the parameter, the method and the limit the lot was released against. A row that reads “conforms” without the test behind it asks the reader to accept a conclusion. The table below is the catalog release panel for zinc malate, not a result for any particular lot.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to off-white, free-flowing powder |
| Identification | Infrared spectrum and HPLC retention | Conforms to the reference |
| Assay, as zinc malate | HPLC | 98.0–102.0% |
| Zinc (Zn) | Complexometric titration | 32.0–34.0% |
| Loss on drying | Gravimetric | ≤2.0% |
| Heavy metals | ICP-MS, element panel | Lead ≤3 · arsenic ≤2 · cadmium ≤1 · mercury ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | Aerobic count ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli, Salmonella: absent |
| Particle size | Sieve analysis, 40 mesh | ≥95% passing |
The assay, the zinc figure and the basis
The HPLC line and the titration line measure different things. The assay is a chromatographic result expressed as zinc malate; the zinc line is a titration of the element, usually with disodium edetate at about pH 10 and an indicator such as Eriochrome Black T. The titration counts zinc from every source in the portion that dissolves. It does not know whether that zinc arrived as malate, citrate or oxide.
That is why the two results have to be read together. Pure zinc malate, C4H4O5Zn, has a formula weight of about 197.45 and carries 33.1% zinc by mass. A lot at 99.0% assay should therefore report about 32.8% zinc. A zinc figure well above that ratio points to a second, denser zinc source such as oxide; a figure below it points to dilution or to a salt with a lower zinc fraction.
The basis must be stated, not assumed. A dried-basis figure has the measured water taken out of the calculation, while an as-is figure still contains it. With a drying limit of ≤2.0% the gap between the two is small, but it is not zero, and it is largest in the lots that were handled least carefully. The certificate should write “as-is” or “dried basis” in the assay and zinc rows themselves, not in a footnote.
The limit, the result and the gap between them
A release limit is the boundary the specification sets; a batch result is the measurement the laboratory returned. The certificate needs both, in separate columns and next to the method, so the reader can see how far the lot sat from the edge.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 98.0–102.0% | Measured percentage, with the basis |
| Zinc | 32.0–34.0% | Measured percentage and titration method |
| Loss on drying | ≤2.0% | Measured percentage |
| Heavy metals | Per element | A mg/kg figure for each element |
| Microbiology | Counts and absence | The count plus the absence statement |
Not every line is a range. Identification is a pass or fail against a reference, and the absence tests are pass or fail against the method. The metal panel works differently: each element has its own ceiling, and a single “heavy metals” total hides the one that matters. Ask for the limit of quantification beside any “less than” result; without it the number describes the method, not the powder.
What moves between batches
The reaction, the crystallisation and the drying step move the assay, the zinc figure and the loss on drying. Milling and sieving move the particle-size result without changing the chemistry, so a change from 40 mesh to a finer cut should not be offered as an explanation for an assay shift. Colour is the least quantitative line: white to off-white covers a range, and a cream or grey tint is a reason to look at the drying record and the metal panel, not to reject on sight.
A trend across lots is more informative than one result near an edge. Zinc drifting high with the assay steady suggests a second zinc source; zinc drifting low with the drying result climbing suggests moisture; both numbers falling together suggests a carrier. One lot code should appear on the certificate, the pouch, the drum and the retained sample, so a trend can be attached to a pack rather than to a supplier in general.
When to order an outside test
An outside laboratory earns its cost in four situations: a new source that has not been qualified, a first entry into a regulated market, a salt claim the supplier's paperwork cannot support, and a result that is disputed. Do not repeat the whole certificate; choose the tests that answer the open question. Infrared and HPLC settle the malate, EDTA titration settles zinc, Karl Fischer or loss on drying settles water, ICP-MS covers the elements and a plate count covers the hygiene. If crystalline zinc oxide is suspected, add diffraction, because titration cannot distinguish the sources.
Chain of custody decides whether the test settles anything. The sample tested should be the retained sample, and the report should name the lot. When two laboratories disagree, give the referee the retained sample, the specification and both reports, and ask for the test that separates the forms rather than a second run of the same assay.
How two suppliers compare
Put six lines side by side: the salt name and CAS number 2847-05-4; the assay result and its basis; the zinc result and the titration method; the loss on drying; the contaminant and microbiological panel; and the pack size with its lot code. Two quotations that agree on the zinc percentage but differ on the assay, the moisture or the basis are not describing the same powder.
Traceability is the next layer. The certificate should name the manufacturing site, the release date and the specification version it was released against. The catalog line sits on the zinc malate product page. The tests that separate the salt from a blend are on the identity page; the titration is described in the complexometric method note; the release workflow is on the quality page. The zinc citrate page shows the parallel panel for the other salt.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation