01 COA & batch testing

What the COA for zinc lactate actually contains

Technical document 01 · Reviewed 2026-11-19 · Zinc Lactate

On this page
  1. The certificate as a set of auditable lines
  2. Assay basis, water of crystallisation and the zinc figure
  3. The limit, the result and the gap
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

For a zinc lactate lot the certificate reports appearance, identification by infrared and titration, assay and elemental zinc by titration, water by Karl Fischer, heavy metals, microbiology and particle size. Every row needs its method, its limit and this lot's result; the ranges below are catalogue limits, not a lot result. The hydrate belongs in the product name and the water figure belongs beside the zinc figure, because zinc lactate trihydrate is defined by both.

In one line

The zinc figure and the water figure have to agree: a 21.0–23.0% zinc result describes zinc lactate trihydrate only when the 17.0–19.0% water and the lactate identity are read beside it.

The certificate as a set of auditable lines

A reader should be able to audit any row without a second document: what was tested, how, against which limit, and what the lot returned. “Conforms” alone is a verdict without a number. The identity row settles the anion; the zinc and water rows settle how much trihydrate the powder contains.

Identity, assay and physical tests · zinc lactate trihydrate
ParameterMethodRelease limit
AppearanceVisualWhite crystalline powder
IdentificationInfrared spectrum and titrationConforms to reference
AssayComplexometric titration98.0–102.0%; basis stated on the certificate
Zinc (Zn)Complexometric titration21.0–23.0%
WaterKarl Fischer17.0–19.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Assay basis, water of crystallisation and the zinc figure

Zinc lactate trihydrate is 18.16% water and 21.97% zinc by formula. The catalogue pairs water at 17.0–19.0% with zinc at 21.0–23.0%, so a lot that meets both is consistent with the trihydrate. A lot whose water falls below 17.0% while zinc rises above 23.0% has lost lattice water; it is a different solid, even if the assay still reads inside its range.

The assay needs its basis in the same row. Calculated on the dried basis as anhydrous zinc lactate, 99.0% with 18.0% water gives 99.0% × (1 − 0.18) × 26.85% = 21.8% zinc as weighed. Calculated on the trihydrate as-is, 99.0% gives 99.0% × 21.97% = 21.75% zinc. Both land inside the catalogue range, but the arithmetic differs; a certificate without the basis leaves the reader guessing.

In the usual complexometric method the assay is calculated from the same EDTA titration as the zinc line. The two numbers are not independent evidence: they rise and fall together. The infrared spectrum and the lactate identity are the separate evidence for the anion; the water result is the separate evidence for the hydrate.

Karl Fischer measures total water, not only surface moisture. That is why 17.0–19.0% is a hydrate specification rather than a drying allowance: a lot at the bottom of the range has little room for water picked up after opening, and a lot at the top may already be carrying it. The measured figure belongs on the certificate.

The limit, the result and the gap

A limit is a gate, while a result is a measurement, and the two need separate columns with the method adjacent. If the result column simply repeats the range, no measurement has been reported, and a “passes specification” line gives nothing to trend.

Reading the result column
ParameterRelease limitResult column
Assay98.0–102.0%, basis namedA measured percentage with the basis and the titration method
Zinc21.0–23.0%A measured percentage on the powder as weighed
Water17.0–19.0%A measured percentage by Karl Fischer
Heavy metalsPer elementA measured figure in mg/kg for each element, with the quantification limit
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 40 meshThe measured percentage through the sieve

“Conforms” is a conclusion, not a measurement. The heavy-metal evidence is a figure per element, not a total; a summed result hides the element that matters. Microbiology needs a count and an absence statement, with the method named. A “not detected” line without a detection limit says something about the method, not the powder.

What moves between batches

Crystallisation and drying move water and zinc together. A drier lot loses surface moisture first and lattice water later; as water falls, zinc rises because the same metal sits in less mass. A wetter lot moves the other way: zinc falls, water rises, and the powder can cake. Both are visible on the certificate before the drum.

The assay and zinc line come from the same titration, so they cannot check each other. Lactate identity should not move: an infrared spectrum that no longer matches the reference is a different signal from a small zinc shift. Particle size moves with milling and sieving, not chemistry, so a change in the 40 mesh result does not imply a change in the salt.

Appearance and flow resist quantification, yet they often flag a change before a number does. A grey or yellow cast, or a sudden loss of flow, should send the reader to the drying record and the metal panel: the assay can still be in range. Several lots in sequence tell more than one result at the edge. Pouch, drum and retained sample should share a lot code.

When to order an outside test

An outside laboratory earns its place for a new source, a regulated-market first shipment, a form claim the certificate cannot carry, or a disputed result. Build the panel around the open question: EDTA for zinc, HPLC or infrared for lactate, Karl Fischer for water, ICP-MS for the metals, a microbiology set, and X-ray diffraction if crystalline zinc oxide is suspected.

Every trace and phase method should come with its detection or quantification limit. The material tested needs to be the retained sample, with a lot code matching the certificate and the pack. In a dispute, hand the referee that sample, the specification and the certificate, then request the tests that distinguish forms rather than a repeat titration.

What to compare between suppliers

A fair comparison reads across six lines: the hydrate and CAS number, the assay with its basis, zinc and water, the identity method and its reference, the contaminant and microbiology panel, and the mesh and pack. Quotations that match on zinc but part company on basis or water are offers for different powders.

Traceability is the second layer. The document should identify the manufacturing site, the lot and the release date, and the same lot code should be printed on pouch, drum and retained sample. The catalogue specification sits on the zinc lactate product page; the tests that prove the anion are on the identity page; the hydrate and mesh options are on the grades page; the titration is described in the methods library; the release file is explained on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation