06 Identity & adulteration

How to prove a zinc lactate lot is the lactate

Technical document 06 · Reviewed 2026-11-19 · Zinc Lactate

On this page
  1. The four identity layers
  2. The 1:2 ratio and the water
  3. XRD and the solid-state question
  4. What substitution looks like
  5. Writing identity into the specification
  6. Questions to put to a supplier

Four independent lines make a zinc lactate lot: the paperwork names the trihydrate and the CAS number, infrared and HPLC establish the lactate anion, EDTA titration returns 21.0–23.0% zinc, and Karl Fischer returns 17.0–19.0% water. Zinc alone cannot separate the lactate from zinc sulfate, whose heptahydrate carries a very similar zinc percentage. The anion and the water finish the identification.

In one line

The zinc figure, the lactate peak, the 17.0–19.0% water and the 1:2 zinc-to-lactate ratio are separate checks, and a lot is the lactate only when they agree.

The four identity layers

Each layer answers a different question, and one result can close one layer while leaving the others open. The table sets out what each test proves and what it does not. A supplier who answers only the zinc figure has described a quantity, not a material.

Four checks on a zinc lactate lot
CheckWhat it settlesMethodWhat the result covers
PaperworkHydrate and identityName, CAS number, formulaThe label on the lot, nothing more
MetalZinc contentComplexometric EDTA titrationThe element, not the anion
AnionLactate presentInfrared spectrum and HPLCThe salt, not the hydrate
Water and ratioTrihydrate and stoichiometryKarl Fischer and mole calculationThe hydrate, not the purity alone

The paperwork layer is needed because the trihydrate and the anhydrous salt differ in formula weight and zinc figure. The metal layer is EDTA titration, which measures total zinc in the dissolved portion and says nothing about the anion. The anion layer pairs an infrared spectrum, matched against a reference in the carboxylate and hydroxyl regions, with an HPLC separation of lactate from other organic acids. The water layer is Karl Fischer, read together with the mole ratio.

The 1:2 ratio and the water

Zinc lactate is Zn(C3H5O3)2·3H2O. In a formula weight of about 297.6, zinc accounts for 21.97%, the two lactate anions for 59.87% and the three waters for 18.16%. Charge balance fixes the mole ratio at one zinc to two lactate: zinc is divalent and lactate is monovalent. Any other ratio implies a second ion or a different anion.

When a certificate reports lactate quantitatively, convert zinc and lactate to moles and look for the 1:2 ratio. That assay is not part of the routine release panel; it belongs to a disputed lot or a new source. Excess lactate against zinc suggests added lactic acid or a diluted salt, while excess zinc against lactate suggests a second zinc source. Compare both on the same basis.

The water figure is the simplest discriminator. Zinc sulfate heptahydrate carries 22.74% zinc, close enough to the lactate's 21.97% that a zinc assay alone cannot tell them apart, but it carries about 43.9% water against the lactate's 18.16%. A Karl Fischer result near 18% with 22% zinc is consistent with the lactate; a result near 44% is not. A sulfate limit test adds a direct check on the anion.

XRD and the solid-state question

X-ray diffraction maps crystalline phases. Here it can flag crystalline zinc oxide, match the hydrate pattern to a reference, and show whether two lots are the same solid. It is neither a purity assay nor a measure of anion or water. A report claiming “XRD conforms” without the pattern, the reference and the detection limit adds little.

Reach for diffraction when the question is solid form, not potency: a suspected oxide addition, a trihydrate-to-anhydrous switch, or a new source claiming the same specification. It is not a routine release test here. Before accepting a “no crystalline zinc oxide detected” line, ask for the sample preparation and the detection limit.

What substitution looks like

Zinc lactate substitutions and the signals
SubstitutionWhat movesSignalTest
Zinc oxideZinc rises, water falls, powder less solubleZinc above 23%; low waterKarl Fischer, XRD, solubility
Zinc sulfateZinc stays near 22%; water rises to about 44%High water; sulfate presentKarl Fischer, sulfate test
Zinc gluconateZinc falls toward 14%; lactate signal weakensLow zinc; no lactate peakHPLC, infrared
Anhydrous sold as trihydrateWater falls below 17%; zinc risesWater and zinc outside the pairKarl Fischer; hydrate declaration
Lactose or carrierZinc and assay fall togetherLow zinc; foreign infrared bandsMass balance, infrared

Zinc oxide is the blunt route: at about 80% zinc, a small addition lifts the zinc figure and pulls the water down while the powder stays white. Zinc sulfate is subtler because its zinc figure is so close; the water result and a sulfate test are what expose it. Zinc gluconate pulls the zinc figure down, and a lactose carrier dilutes zinc and assay together.

Writing identity into the specification

  • “Zinc lactate trihydrate, CAS 16039-53-5, C6H10O6Zn·3H2O; hydrate named on the certificate.”
  • “Assay 98.0–102.0% by complexometric titration; basis stated on the certificate.”
  • “Zinc 21.0–23.0%; water 17.0–19.0% by Karl Fischer.”
  • “Identification by infrared and titration; lactate identity by HPLC where the anion is disputed.”
  • “No added zinc oxide, zinc sulfate, zinc gluconate, lactic acid or undeclared carrier.”
  • “Sieve: ≥95% through 40 mesh; contaminants and microbiology per the panel.”

The prohibitions matter as much as the numbers. A zinc range by itself cannot rule out a second zinc source, and a supplier cannot be bound by a restriction the specification never writes down.

Questions to put to a supplier

  1. What hydrate is this lot, and what CAS number appears on its certificate?
  2. Which zinc and water results belong to the lot, and were both measured on one sample?
  3. May we see the infrared spectrum and, where the anion is disputed, the HPLC chromatogram?
  4. Does the lot contain one salt, or a blend with oxide, sulfate, gluconate or a carrier?
  5. If identity is disputed, will you join a re-test on the retained sample?

Five direct answers amount to an identity file; a lone zinc percentage does not. The product hub holds the catalogue line; the COA page maps each figure onto the certificate; the grades page compares the hydrate and mesh options; the methods library sets out the titration and chromatography; the quality page explains the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation