06 Identity & adulteration

How to prove a lot is tricalcium phosphate

Technical document 06 · Reviewed 2026-11-20 · Tricalcium Phosphate

On this page
  1. Five layers, five questions
  2. The calcium-to-phosphorus ratio
  3. X-ray diffraction and the solid phase
  4. What substitution looks like
  5. Identity clauses for the specification
  6. Five questions for the supplier

A lot is tricalcium phosphate when the document, the calcium result, the phosphorus result and the calculated molar ratio agree, and the diffraction pattern matches the phase named. The ratio is the discriminator: pure tricalcium phosphate is 1.5 mol Ca per mol P, dicalcium phosphate is 1.0, and hydroxyapatite is 1.67. Calcium alone cannot tell them apart.

In one line

Identity is the calcium figure, the phosphorus figure and their molar ratio agreeing, with a solid-state pattern that matches the phase named on the certificate.

Five layers, five questions

A certificate can carry the right name and still leave the powder unproven. Each layer below asks a different question and needs its own evidence; an answer to the first alone describes the paperwork, not the material.

Layers of tricalcium phosphate identity
LayerQuestionTestWhat it proves
DocumentAre the name, CAS and grade named?Specification and labelPaperwork only
CalciumIs the calcium figure right?Complexometric titration with EDTAThe element, not the salt
PhosphorusIs the anion phosphate?Titration or spectrophotometry after digestionThe phosphate anion
RatioIs the Ca : P balance that of tricalcium phosphate?Calculation from the two resultsWhich calcium phosphate
Solid stateWhich phase is present?X-ray diffractionTricalcium phosphate against apatite or a second phase

Acid-insoluble matter is a useful negative check beside these: it measures what the acid did not dissolve, so a high residue caps how much of the powder can be silica or a silicate. It does not identify the salt.

The calcium-to-phosphorus ratio

Pure Ca₃(PO₄)₂ is 38.76% calcium and 19.97% phosphorus. The mass ratio is 1.94; the molar ratio is (38.76 ÷ 40.078) ÷ (19.97 ÷ 30.974) = 1.50. The conversion between the two is constant: multiply the mass ratio by 0.773 to get the molar ratio.

The calculation is portable because it needs only the two results the certificate already carries. A lot at 38.0% calcium and 19.0% phosphorus has a molar ratio of 1.55; a lot at 36.0% calcium and 19.0% phosphorus has 1.46; a lot at 35.0% calcium and 19.5% phosphorus has 1.39. The last lot passes both catalog windows and is still not stoichiometric tricalcium phosphate.

The catalog windows are independent, so they allow molar ratios from about 1.31, at 34% calcium and 20% phosphorus, to about 1.72, at 40% calcium and 18% phosphorus. A stoichiometric product sits at 1.50; an apatitic product sits higher, toward the 1.67 of hydroxyapatite. The agreed ratio window is therefore a real specification line, not a derived curiosity.

Neighbouring salts sit outside the window. Dicalcium phosphate is 1.0; monocalcium phosphate is 0.5; hydroxyapatite is 1.67. Calcium carbonate and calcium sulfate carry no phosphorus at all, so their phosphorus result is near zero and the ratio is undefined. Each of those is visible in the pair of figures, and none is visible in the calcium figure alone.

X-ray diffraction and the solid phase

X-ray diffraction asks which solid is present. β-tricalcium phosphate, the whitlockite-type phase, gives one pattern; α-tricalcium phosphate, the high-temperature phase, gives another; hydroxyapatite gives a third. A commercial lot can be a mixture, and a broad or apatitic pattern is a phase result rather than a purity failure.

The scan separates a physical blend from a single phase, and it shows a dicalcium phosphate or calcium carbonate line when either is present above the detection limit. It cannot quantify an amorphous fraction, and it cannot see a substitution that leaves the lattice unchanged. Before accepting a “match” statement, ask for the reference pattern, the scan range, the sample preparation and the detection limit.

For a disputed lot, diffraction plus calcium plus phosphorus plus the ratio is stronger than any one of them. Diffraction is not a routine release test for this product, and a certificate that says only “XRD conforms” without the pattern has added little.

What substitution looks like

Substitutions and the signals that expose them
SubstituteWhat it doesSignalTest
Dicalcium phosphateRaises phosphorus; lowers the ratio toward 1.0Phosphorus above 20%; calcium below 34%Ratio, XRD
Calcium carbonateRaises calcium; adds no phosphorusEffervescence in acid; phosphorus near zeroAcid reaction, phosphorus, XRD
Calcium sulfateMatches some calcium figures; adds no phosphorusPhosphorus near zero; sulfate test positivePhosphorus, sulfate test
HydroxyapatiteRaises the ratio toward 1.67Calcium high against phosphorusRatio, XRD
Silica or silicateDilutes both figures; adds residueAcid-insoluble matter highAcid-insoluble matter, XRD
Feed-grade materialSame chemistry, different contaminant panelFluoride or metals outside the food limitFluoride, ICP-MS, documents

Colour is the weakest signal. All of these can be white, and the strongest evidence is the phosphorus figure, the ratio and the acid-insoluble residue. A certificate that reports calcium and appearance but not phosphorus has not tested the substitution that matters most.

Identity clauses for the specification

  • “Tricalcium phosphate, CAS 7758-87-4, Ca₃(PO₄)₂; grade and phase declared.”
  • “Calcium 34.0–40.0% and phosphorus 18.0–20.0%, both on the same stated basis.”
  • “Calculated Ca : P molar ratio reported; agreed window stated.”
  • “Loss on drying ≤2.0%; acid-insoluble matter reported.”
  • “X-ray diffraction on request, with the reference pattern and the detection limit.”
  • “No dicalcium phosphate, calcium carbonate, calcium sulfate or silica added.”

Five questions for the supplier

  1. What are the calcium and phosphorus results, and were both measured on the same lot and basis?
  2. What is the calculated molar Ca : P ratio, and what window does the specification set?
  3. Which phase does X-ray diffraction show, and against which reference pattern?
  4. What is the acid-insoluble matter, and what does it rule out?
  5. What is the fluoride figure, and will you re-test the retained sample jointly if a result is disputed?

Five direct answers amount to an identity file; a calcium percentage does not. The product hub carries the catalog figures; the COA page shows where each figure sits; the grade page covers the phase and the particle form; the tricalcium versus dicalcium page takes the ratio arithmetic further; the methods index describes the tests.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation