01 COA & batch testing

What a tricalcium phosphate COA reports, line by line

Technical document 01 · Reviewed 2026-11-20 · Tricalcium Phosphate

On this page
  1. What the certificate has to carry
  2. The oxide basis, the drying basis and the ratio
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

A tricalcium phosphate certificate is read on four lines: calcium, phosphorus, the ratio between them, and loss on drying. The catalog range is 34.0–40.0% calcium and 18.0–20.0% phosphorus, each released against a named method. The certificate records one lot; the specification records the window it had to meet.

In one line

A tricalcium phosphate certificate is read on two elements and their ratio: calcium and phosphorus, each with its method and its basis, because the ratio is what separates this salt from dicalcium phosphate.

What the certificate has to carry

Every line should name the analyte, the method and the gate the lot had to pass. A line that says only “conforms” cannot be checked against the specification or trended across lots. Identification is a pair of wet reactions: calcium gives a white oxalate precipitate, and phosphate gives a yellow phosphomolybdate precipitate in nitric acid. Both have to match before the elemental figures are read.

Release parameters for tricalcium phosphate
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationCalcium and phosphate reactionsConforms to the reference
CalciumComplexometric titration with EDTA34.0–40.0%
PhosphorusTitration after acid digestion18.0–20.0%
Loss on dryingGravimetric, oven≤2.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Calcium and phosphorus are separate determinations: calcium by EDTA, phosphorus by titration after acid digestion, with spectrophotometry as the usual cross-check.

The oxide basis, the drying basis and the ratio

Calcium is reported here as the element, not the oxide. The factor is 56.077 ÷ 40.078 = 1.399, so 38.0% calcium is 53.2% CaO. Phosphorus is reported as the element, not as P₂O₅: 141.944 ÷ 61.948 = 2.291, so 19.0% phosphorus is 43.5% P₂O₅. A technical data sheet that quotes 53% CaO and 43% P₂O₅ may describe the same powder as 38% Ca and 19% P; convert to one basis before comparing.

Loss on drying is the second basis. The catalog limit is ≤2.0%, and a dried-basis result is larger than the as-received figure by the moisture fraction: 38.0% calcium as received with 1.5% loss on drying reads 38.58% dried. The basis belongs in the row, not in a footnote.

The ratio is the third derived figure. Pure Ca₃(PO₄)₂ is 38.76% calcium and 19.97% phosphorus: 1.94 by mass, 1.50 by mole. The catalog windows are independent, so a lot at 34% calcium and 20% phosphorus passes both with a molar ratio near 1.31, which is not the TCP stoichiometry. Calculate the ratio and report it beside the two results.

If a supplier also reports an assay calculated as Ca₃(PO₄)₂, ask which element produced it: 36.0% calcium calculates to 92.9%, while 19.0% phosphorus calculates to 95.1% on the same lot. An assay without its calculation is a third number, not a check on the first two.

Release limit versus batch result

A limit is the gate; a result is what the laboratory found. The two belong in separate columns, with the method beside them. If the result column repeats the range, the lot has not been reported.

What the result column should contain
ParameterRelease limitResult column
Calcium34.0–40.0%A measured percentage, with the basis and the titration method
Phosphorus18.0–20.0%A measured percentage, with the digestion and determination method
Ca : P molar ratioNo catalog gate; agree a windowThe calculated figure, from results on one basis
Loss on drying≤2.0%A measured percentage, with oven temperature and time
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

The ratio line is calculated, not measured. The catalog sets no ratio gate, and the elemental windows do not pin the stoichiometry on their own. Agree a ratio window when the phase matters, and report the calculated figure on every lot.

What moves between batches

Phosphate source, precipitation pH and calcination temperature move calcium and phosphorus together or apart. A change that raises calcium without raising phosphorus pushes the ratio toward apatite; a change that raises phosphorus without calcium pushes it toward dicalcium phosphate. Both can stay inside the catalog windows, which is why the ratio is read as a trend.

Drying moves loss on drying. Milling moves the 80 mesh result and nothing else in the chemistry. Fluoride is the contaminant to watch when the phosphate comes from rock; it is not on the catalog panel, and a destination specification may set a limit.

Colour is descriptive. White to off-white covers a range, and a grey or cream tone is not a purity figure. A lot visibly darker than the retained sample is worth a source question, not a rejection on appearance.

When to order an outside test

Order an outside test for a new source, a first shipment into a regulated market, a disputed ratio or an open phase question. The panel is not a copy of the certificate: calcium by EDTA with the indicator named, phosphorus by spectrophotometry with the digestion described, loss on drying with the oven temperature and time, ICP-MS for the metals, microbiology and the sieve result.

Add X-ray diffraction when the phase is disputed, fluoride when the destination sets a limit, and acid-insoluble matter when a silica dilution is suspected. Ask for the detection limit beside every “not detected” entry; without it, the entry does not say how much could have been present.

Keep the chain of custody. The sample tested should be the retained sample, the report should carry the lot code and the specification revision, and a contested result should go to a joint re-test on the retained powder.

What to compare between suppliers

Six lines show whether two offers describe the same powder: name and CAS number; calcium and phosphorus with methods and basis; loss on drying; the calculated ratio; heavy metals and microbiology; particle size, plus bulk density and flow if the powder will be compressed.

Two offers that agree on calcium but differ on phosphorus are not the same salt, and an offer that reports calcium as CaO without saying so is not comparable until converted. The lot code on the certificate should match the pouch, the drum and the retained sample.

The catalog figures sit on the tricalcium phosphate product page. The dicalcium phosphate page carries the neighbouring salt and its ratio; the methods index describes the assays; the quality page sets out the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation