02 Grade comparison

Tricalcium phosphate grades: powder, granulation and phase

Technical document 02 · Reviewed 2026-11-20 · Tricalcium Phosphate

On this page
  1. Why one name covers several powders
  2. The grades side by side
  3. Particle, flow and the acid reaction
  4. Dose arithmetic and the dosage form
  5. What to write into the specification
  6. When another salt is the better choice

Tricalcium phosphate is a family name, not a single grade. The catalog powder is 80 mesh with 34.0–40.0% calcium and 18.0–20.0% phosphorus; the solid behind those figures can be stoichiometric tricalcium phosphate or a calcium-deficient apatite, and granulation or a toothpaste-grade selection changes the physical powder without changing the formula. The grade decision is the ratio and the phase first, then the particle form.

In one line

The grade of tricalcium phosphate is set by its calcium-to-phosphorus ratio, its crystal phase and its particle size, not by the name on the drum.

Why one name covers several powders

The pure formula Ca₃(PO₄)₂ is 38.76% calcium and 19.97% phosphorus, a molar Ca : P ratio of 1.5. Food-grade material is often made by neutralising phosphoric acid with a calcium source, then drying or calcining the precipitate. The temperature and the calcium dose decide how much of the product is crystalline tricalcium phosphate and how much is a calcium-deficient apatitic phase with a ratio below the 1.67 of hydroxyapatite. The current EU additive definition for E 341(iii) describes the material as a variable mixture of calcium phosphates for this reason.

The catalog window is wide enough to cover that variation: 34.0–40.0% calcium and 18.0–20.0% phosphorus. The purchase specification therefore has to say more than “tricalcium phosphate”; it has to name the ratio window and the physical grade.

The grades side by side

Tricalcium phosphate grades and the neighbouring salt
GradeCalcium and phosphorusFormUsual fit
Catalog powder34.0–40.0% Ca; 18.0–20.0% PPowder, ≥95% through 80 meshCapsules, tablets, powder blends
GranulatedSame chemistry as the baseAgglomerated, on requestFlow and dust control on a press
Toothpaste-grade selectionSame chemistry; physical lines agreedPowder, on requestOral-care abrasive and calcium source
Dicalcium phosphate29.0–30.0% Ca; 22.0–23.5% PAnhydrous powder, 40 meshA different salt with a 1 : 1 molar ratio

The first row is the catalog grade. The second and third are physical selections of the same chemistry, and each one needs its own specification lines: a granulated lot is judged on flow and bulk density, while a toothpaste selection is judged on particle distribution, whiteness and abrasivity as agreed with the buyer. The fourth row is not a grade of tricalcium phosphate at all; it is the neighbouring salt, and the dicalcium phosphate page covers it.

Feed-grade and technical-grade material sit outside this specification: the contaminant panel, the documentation and the intended use are different, even when the calcium figure looks similar.

Particle, flow and the acid reaction

Tricalcium phosphate is practically insoluble in water and dissolves in dilute acid. In a dry blend or a capsule it is a dense, free-flowing powder; in water it is a suspension that settles, and no amount of mixing turns it into a clear solution. A formulator who needs clarity has to change the salt, not the mesh.

The catalog fixes ≥95% through 80 mesh. Bulk density, flow and compressibility are not on the catalog list, and they decide whether the powder runs on a press. Granulation improves flow and reduces dust, but it also changes the fill weight for the same volume, so the tablet or capsule trial has to run on the granulated grade that will be bought.

The acid reaction is the other physical difference. A finer powder presents more surface to the acid and reacts faster; a coarse or calcined powder reacts more slowly. In a tablet this affects disintegration and mouthfeel, and in a suspension it affects how much grit the consumer notices.

Dose arithmetic and the dosage form

Calcium is the figure the label declares, so the salt weight follows from the calcium content. At the theoretical 38.76% calcium, one gram of tricalcium phosphate carries about 388 mg of calcium and about 200 mg of phosphorus. A 600 mg calcium claim therefore needs about 1.55 g of the salt and brings about 309 mg of phosphorus with it. At 34.0% calcium the same claim needs about 1.76 g.

The dosage form follows the mass. A 1.55 g fill is two or three large capsules, or one large tablet; the powder compacts well and is also used as a tablet diluent, so a tablet can carry tricalcium phosphate as the calcium source and as part of the filler at the same time. The calcium on the label is then the sum of both uses, and the diluent has to be counted as an active ingredient.

A powder blend or a stick pack takes the 80 mesh powder and disperses it; the consumer sees a white suspension, not a clear drink. A toothpaste takes a selected grade where the particle size and the abrasivity are agreed with the buyer. In every format, the dose is a calcium decision and a phosphorus decision at once.

What to write into the specification

  • “Tricalcium phosphate, CAS 7758-87-4, Ca₃(PO₄)₂; food grade.”
  • “Calcium 34.0–40.0% by complexometric titration; phosphorus 18.0–20.0% by titration after digestion.”
  • “Calculated Ca : P molar ratio reported; the agreed window stated.”
  • “Loss on drying ≤2.0%; particle size ≥95% through 80 mesh.”
  • “Heavy metals Pb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 mg/kg; microbiology as listed.”
  • “Crystal phase and source declared; no dicalcium phosphate, calcium carbonate or silica added.”
  • “Granulated or toothpaste-grade selection named, with its own physical lines, if either is ordered.”

The negative clause matters. The two elemental windows are wide and independent, so a blend of two calcium phosphates with different ratios can be built to pass both lines: a calcium-rich apatitic powder diluted with dicalcium phosphate is one example. The calculated ratio and the diffraction pattern are what expose the blend, so both belong in the specification.

When another salt is the better choice

If the product has to be a clear solution, tricalcium phosphate is the wrong salt: it is insoluble in water and dissolves only by reacting with acid. If the matrix is acidic and must stay clear, a soluble calcium salt such as calcium citrate or calcium lactate is the practical starting point. If the formula needs more calcium per gram, calcium carbonate carries about 40% and is the compact alternative when its acid reaction is acceptable.

If the label names dicalcium phosphate, tricalcium phosphate is not a gram-for-gram substitute: the calcium rises, the phosphorus falls and the tablet mass changes. The tricalcium versus dicalcium page sets out that arithmetic and the label consequence.

The product hub carries the catalog figures; the COA page shows how the two elemental lines are reported; the identity page covers the ratio and the diffraction check; the methods index describes the assays.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation