06 Identity & adulteration

How we prove a potassium iodide lot is the named salt

Technical document 06 · Reviewed 2026-11-19 · Potassium Iodide

On this page
  1. Four checks, one identity
  2. The iodide-to-assay ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A potassium iodide lot is the named salt when four lines agree: the document names KI and CAS 7681-11-0, IR matches the reference, titration gives 99.0–101.5% assay with 75.0–78.0% iodide, and loss on drying is ≤1.0%. The iodide figure against the assay should land near the theoretical 76.45% iodine fraction. A low iodide figure with a normal assay points to a diluent or to oxidation.

In one line

Identity is the agreement between the iodide figure, the assay and the water: any one of them alone can describe a different white salt.

Four checks, one identity

Identity is not one test. It is four answers that have to agree, and each answer rules out a different mistake. The document layer rules out a naming error. IR rules out the wrong salt family. Titration measures the iodide and the assay. The water result decides how much of the weighed powder is not the salt. A supplier who supplies only the first answer has supplied a label, not evidence.

Four checks that together identify potassium iodide
CheckQuestion it answersMethodWhat it establishes
DocumentIs the salt named?Name, CAS number, formulaPaperwork only
SpectroscopyIs the salt the reference material?IR against a referenceThe salt family
TitrationHow much iodide and how much KI?Titration for assay and iodideThe amount and the iodine fraction
WaterHow much of the powder is water?Loss on dryingThe mass balance

The checks are routine except for a disputed lot. What separates a good file from a thin one is not the method list but whether the figures are reported, and whether they share a basis.

The iodide-to-assay ratio

The theoretical iodine fraction is 126.90 ÷ 166.00 = 76.45%. The catalog pairs 99.0–101.5% assay with 75.0–78.0% iodide, and the ratio makes the two windows consistent: 99.0% × 0.7645 = 75.69%, and 101.5% × 0.7645 = 77.60%. A lot that reports 100.0% assay and 70.0% iodide is not a slightly low iodide lot; the two figures do not describe the same powder.

A low iodide figure with a normal assay is the signature of a white diluent or of oxidation. Potassium chloride and sodium chloride are white and free-flowing, and a certificate that reports only the assay can miss them; chloride by ion chromatography, or sodium and potassium by ICP-OES, separates them. Oxidation leaves free iodine, which shows as a yellow tint, a higher free-iodine result and a pH shift in solution.

The ratio is a cross-check, not a release test, and it only works when both figures share a basis. An as-is assay compared with a dried-basis iodide figure can look inconsistent when the lot is fine. State the basis before drawing a conclusion.

X-ray diffraction and the solid state

X-ray diffraction answers a different question: is the solid crystalline, and does the pattern match potassium iodide? KI crystallises in the cubic system, and its lattice spacing differs from potassium chloride, potassium bromide and sodium chloride, so a reference pattern separates the white salts that a visual check cannot. An amorphous diluent gives a broad halo instead of sharp reflections.

XRD is not a routine release test for this product. A certificate that says “XRD conforms” without the pattern, the scan range and the reference has added little. Ask for those three things if the solid form is disputed. On a disputed lot, XRD, titration and water together are stronger than any one of them.

What adulteration looks like

Common potassium iodide substitutions and the signals
MaterialWhat it doesSignalTest
Potassium chlorideWhite diluent; lowers iodineIodide low; potassium normal or high; chloride highIon chromatography, titration
Sodium chlorideWhite diluent; lowers iodineIodide low; sodium highICP-OES, ion chromatography
Potassium bromideWhite diluent; interferes with some assaysBromide high; iodide lowIon chromatography
Potassium iodateDifferent iodine figure and oxidising behaviourIodate test positive; assay behaviour differsIodate-specific test, titration
Dextrose or maltodextrinWhite diluent; raises loss on dryingIodide low; water or organic content highLoss on drying, IR, titration
WaterDilutes the powder; cakes itLoss on drying high; as-is assay lowLoss on drying

Colour is the weakest signal. White covers a wide range, and a blend can reproduce it. The stronger signals are the iodide figure against the assay, the water result and the chloride or bromide figure.

Writing identity into the specification

  • “Potassium iodide, CAS 7681-11-0, KI.”
  • “Assay 99.0–101.5% by titration; state the basis.”
  • “Iodide 75.0–78.0% by titration; state the basis.”
  • “Loss on drying ≤1.0%.”
  • “Identification by IR and titration, against a reference.”
  • “Free iodine or reducing agents within the agreed limit; report the method.”
  • “Heavy metals and microbiology as listed on the catalog specification.”
  • “No substitution of another iodide salt or a dilution without written change control.”

Five questions for the supplier

  1. Which salt and CAS number is this lot, and which physical form?
  2. Can you provide the IR spectrum and the titration method, not only the assay percentage?
  3. What is the iodide result, and is it on the same basis as the assay?
  4. What is the loss on drying, and what is the free-iodine or reducing-agent result?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the physical forms; the kelp comparison covers the source and label question; the sodium selenite page shows another inorganic salt where oxidation state is the specification; the methods notes explain the titration and IR work.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation