02 Grade comparison

Potassium iodide forms: crystals, powder and dilution

Technical document 02 · Reviewed 2026-11-19 · Potassium Iodide

On this page
  1. Why the form matters more than the assay
  2. The physical forms side by side
  3. Solubility, moisture and handling
  4. Dose arithmetic and blend uniformity
  5. What to write into the specification

Potassium iodide is supplied as crystals, as a 40 mesh powder and, for some projects, as a dilution or premix. The catalog form is the powder; crystals are available on request. The choice is decided by the dosage form and by the small mass of iodide in each dose, not by the assay, which stays 99.0–101.5% across the forms.

In one line

The grade is a handling decision: crystals dissolve cleanly, a 40 mesh powder blends more evenly, and a dilution is what makes a microgram dose weighable.

Why the form matters more than the assay

There is one chemical identity here. Potassium iodide is KI, CAS 7681-11-0, and the assay window does not change with the physical form. What changes is the particle size, the flow, the dust and the way the material can be weighed into a blend. Those are handling properties, and they decide whether a production line can hit the label figure.

The grade question also has a purity side. A technical-grade iodide and a food or supplement grade can share an assay while differing in the heavy-metal panel, the manufacturing controls and the documentation. A technical grade is not the supplement material even when the certificate looks familiar. The specification should name the grade and the destination use before the first order.

The physical forms side by side

Physical forms of potassium iodide and where each one fits
FormWhat it isHandlingTypical fit
CrystalsCoarse crystalline saltLow dust; dissolves readily; can segregate in a blendSolution preparation; a crystal form requested by the customer
40 mesh powderMilled powder, ≥95% through 40 meshFlows and blends more evenly; some dustCapsules, tablets and dry blends
Fine powderMilled below the standard sieveMore dust and static; needs containmentWhen a finer dispersion is required
Dilution or premixKI on a carrier, with a stated assayLets a small dose be weighed accuratelyLow-dose capsules, tablets and sachets

The 40 mesh figure is a sieve result, not a purity claim. A lot that passes 40 mesh is not automatically better than a crystal for every use; it is simply the form the catalog specifies. A dilution is a different specification, with a carrier, an assay and a homogeneity check.

Solubility, moisture and handling

Potassium iodide is freely soluble in water, about 1.4 g per millilitre of water at room temperature, and the solution is neutral to slightly alkaline. The solid is hygroscopic and light-sensitive. Crystals can cake in a humid store; a powder picks up moisture faster because it has more surface, and it can dust or hold static during weighing.

These properties are the reason the pack matters more than the form. A foil pouch or a lined drum is not a marketing detail; it is the barrier that keeps the water below the 1.0% loss-on-drying limit. A clear jar is the wrong container for a light-sensitive iodide, and an open scoop is the wrong way to hold a hygroscopic powder.

The solution should be clear and colourless to very pale. A yellow tint points to free iodine, which is a handling and storage signal rather than a grade difference. The grade cannot repair a pack that lets light and moisture in.

Dose arithmetic and blend uniformity

The label dose is an iodine figure, not a potassium iodide figure. The conversion is fixed: 1 mg of iodine needs 1 ÷ 0.7645 = 1.31 mg of KI. A 150 µg iodine dose needs about 196 µg of KI, and a 220 µg dose needs about 288 µg. If the lot assay is 99.0% on the as-is basis, divide by the assay as well: the same 150 µg dose needs about 198 µg of the powder as weighed.

Those masses are tiny against a normal capsule fill. In a 500 mg capsule, 196 µg of KI is 0.039% of the fill; a direct blend cannot distribute that evenly. A dilution or premix, or a stock solution for a liquid format, is the practical way to get the iodide into the batch. The dilution carrier and the final assay belong in the specification, and the label still declares iodine, not the premix weight.

These are arithmetic examples, not dose recommendations. The formulator and the brand set the label dose; the supplier's job is to make the mass and the assay reproducible.

What to write into the specification

  • “Potassium iodide, CAS 7681-11-0, KI.”
  • “Assay 99.0–101.5% by titration; state the basis.”
  • “Iodide 75.0–78.0% by titration; state the basis.”
  • “Loss on drying ≤1.0%; free iodine or reducing agents within the agreed limit.”
  • “Particle size ≥95% through 40 mesh, or crystals on request.”
  • “Heavy metals and microbiology as listed on the catalog specification.”
  • “Dilution, if used: carrier, assay, homogeneity and label name stated.”

We supply the 40 mesh powder as the catalog form and crystals on request. A dilution is a project specification, not a stock pack. The product hub carries the catalog values; the COA page shows how the assay and iodide are reported; the stability page covers the moisture and light risk; the potassium gluconate page shows a different potassium salt with a very different potassium figure per gram.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation