01 COA & batch testing

What the COA for magnesium taurate actually contains

Technical document 01 · Reviewed 2026-11-18 · Magnesium Taurate

On this page
  1. What the sheet carries
  2. What “dried basis” means for this salt
  3. Release limit versus batch result
  4. What changes between batches
  5. When an outside laboratory helps
  6. Comparing two offers

A magnesium taurate lot is released on a certificate that carries the magnesium assay by complexometric EDTA on the dried basis, the taurate identity by reaction and infrared spectrum, loss on drying, pH, particle size, bulk density and the contaminant panel. The values here are catalog limits, not a batch result. The magnesium line is the one buyers read first and the least specific on the sheet: an oxide-and-taurine blend can be formulated to the same figure.

In one line

The magnesium assay measures the metal, not the salt; the taurate identity and the water are the lines that make the certificate specific.

What the sheet carries

The sheet follows the release specification. Every line should carry the method, the limit and the measured value; without the method the value cannot be checked.

Release parameters · magnesium taurate, catalog specification
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
Magnesium (dried basis)Complexometric EDTA titration8.0–9.0%
IdentificationTaurate reaction and infrared spectrumConforms to reference
Loss on dryingGravimetric, USP <731>≤10.0%
pH (5% suspension)Potentiometry5.0–7.0
Particle sizeSieve analysis≥90% through 60 mesh
Bulk densityTapped cylinder0.50–0.80 g/mL
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and selective mediaAPC ≤1,000 · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent

Microbiology is a second block on the same certificate: aerobic plate count, yeast and mould, E. coli and Salmonella. The limits are set in the specification before release; they are not adjusted to fit the result.

What “dried basis” means for this salt

Dried basis connects the certificate to the drum. The anhydrous salt C₄H₁₂MgN₂O₆S₂ has a formula mass of about 272.6 g/mol; magnesium is 8.9% of that mass and the taurate is 91.1%. A catalog range of 8.0–9.0% says the powder is close to the pure salt, not that it is 98% pure.

The assay is run on a dried sample, so the result is on the dried basis while the drum still contains water. At 9.0% magnesium and 10.0% water, the as-is figure is about 8.1%; at 8.0% and 10.0%, about 7.2%. That tenth of the figure is also a tenth of the label dose if the fill weight is calculated from the dried number. The certificate reports both for a reason.

EDTA measures total magnesium, and other divalent metals consume the titrant unless they are masked. It cannot say which salt supplied the magnesium. The taurate reaction shows that taurine is present; the infrared comparison shows whether it is in the salt or beside it. A certificate with a reaction and no reference spectrum has proved less than it appears to.

The catalog specification does not set a taurine assay. If the label needs a taurine figure, ask for an HPLC result and a calculated Mg : taurate ratio. That is an additional test, not a standard line on the sheet.

Release limit versus batch result

A limit is the gate; a result is the measurement. The certificate should show both with the method. A tick box that says “passes” is a verdict, not a measurement, and it gives the buyer nothing to compare between lots.

Magnesium and loss on drying are read together. A lot at 9.0% with 3% water and a lot at 8.2% with 9% water both pass, but they do not deliver the same magnesium per gram. The pH window of 5.0–7.0 is narrow for a magnesium salt; magnesium oxide is alkaline, and a blend that carries it usually shifts the suspension up. A top-of-range pH is not a failure, but it is a reason to read the identity lines.

The heavy-metal limits here are raw-material limits. The legal limits apply to the product as sold, so a raw-material result only makes sense beside the daily dose and the dilution. Arsenic is an internal limit because the European Union does not harmonise one for supplements. The microbiology limits are fixed in the specification and reported per gram.

What changes between batches

Water is the largest variable. Loss on drying follows the dryer and the crystal form; a lot at 3% and a lot at 9% both pass and behave differently in a hopper. The as-is magnesium, bulk density and caking follow the water.

Particle size and density follow milling and sieving. The 60 mesh line is a floor, not a fixed number, and 0.50–0.80 g/mL is wide enough that two lots can feel like two materials on the press.

pH follows neutralisation and washing; colour follows drying and trace iron. The taurate identity should not move. If the infrared match is marginal, ask for the spectrum and the reference, not another magnesium assay. A result above 9.0% on the dried basis deserves a question, because the pure salt is 8.9%.

When an outside laboratory helps

An outside laboratory earns its place when the supplier is new, when the first shipment enters a regulated market, when the label names the taurate, or when the certificate's identity section is thin. Do not ask for a photocopy of the supplier's panel; ask for the tests that settle the doubt: ICP-MS for the contaminant panel, XRD for crystalline magnesium oxide, FTIR against a taurate reference, Karl Fischer or loss on drying for water, and an HPLC taurine figure if the ratio is in doubt. Send the retained sample, the certificate and the specification, and ask for the discriminating tests.

Comparing two offers

Six lines belong side by side before anything else: the salt name and CAS number, the magnesium method and basis, the taurate identity method and reference, loss on drying and the as-is magnesium, pH with mesh and density, and the oxide screen. If two offers match on 8.5% magnesium and diverge on the other five lines, they describe different powders.

Behind the certificate sits the batch record: who made the lot, which magnesium source, which drying step, and what the retained sample is. The three lot numbers — certificate, drum and retain — should be one number.

The catalog data sit on the magnesium taurate product page. The identity tests are on the identity page, the salt comparison is on the grades page, and the EDTA method is set out in the complexometric titration note. The water figure is defined in the loss-on-drying entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation