What the COA for magnesium gluconate actually contains
A magnesium gluconate certificate carries a short panel: appearance, identity, assay, elemental magnesium, water, the contaminant panel and the physical result. Read together they answer two different questions — is this the gluconate, and how much of it is in the drum — and each line is only useful when it names its method and the limit it was judged against. The values here are the catalog specification; the lot certificate is the document that fixes a particular pack.
The certificate proves the lot in two directions: the titration fixes the magnesium, the infrared spectrum fixes the gluconate, and the water figure closes the mass balance.
Reading the certificate row by row
A reviewer should be able to follow every row from the sample number to the result without asking a question. Three things make that possible: the parameter, the method that produced the figure, and the limit it was judged against. A row that reports “conforms” and nothing else has replaced evidence with a verdict.
Identity and assay do different jobs, and a certificate needs both. Identity establishes that the anion is gluconate rather than another acid; the assay establishes how much magnesium gluconate the lot contains. A high assay with no anion evidence can describe a blend as easily as it describes the salt.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to off-white powder |
| Identification | Infrared spectrum; complexometric titration | Conforms to the reference |
| Assay | Complexometric titration (EDTA) | 98.0–102.0% |
| Magnesium | Complexometric titration (EDTA) | 5.5–6.0% |
| Water | Karl Fischer | ≤1.0% |
| Heavy metals | ICP-MS | Pb ≤3 · Cd ≤1 · As ≤2 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count; pathogen enrichment | APC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent |
| Particle size | Sieve test | ≥95% through 40 mesh |
The basis, the water and the magnesium cross-check
Any percentage needs a denominator. The catalog range is 98.0–102.0%, and the certificate has to say whether that was measured on the powder as it arrived or on the dried substance. Water is capped at 1.0%, so the two readings sit within about a point of each other — enough, though, to decide a borderline lot: 99.0% as received with 0.9% water becomes 99.9% once the water is taken out.
The formula gives the second line its expected value. Magnesium accounts for 24.305 g/mol of the 414.60 g/mol that make up the salt, which is 5.86%. An assay between 98.0% and 102.0% therefore implies magnesium between 5.74% and 5.98%. A lot reported at 99% assay and 5.5% magnesium is not one powder described twice, even if each figure has its own range on the sheet.
When both numbers come from the same EDTA titration they are not independent measurements, and the cross-check tests the laboratory's arithmetic and its basis rather than the material twice. Ask which weighed portion and which dilution were used for each calculation if the two figures sit far apart.
Limit, result and the space between them
A limit is a boundary; a result is a measurement. A certificate that prints the specification range in the result column has told the reader nothing about the lot, and the practice is common enough to be worth checking first.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 98.0–102.0% | A measured percentage, with the basis stated |
| Magnesium | 5.5–6.0% | A measured percentage on the same lot |
| Water | ≤1.0% | A measured percentage by Karl Fischer |
| Heavy metals | Per element | The measured figure in mg/kg for each metal |
| Microbiology | Counts and absence | The plate count plus the absence statement |
| Particle size | ≥95% through 40 mesh | The sieved percentage for this lot |
One summed “heavy metals” number hides the element that matters, and one pass-or-fail microbiology line hides whether the count was 20 cfu/g or 900. The reader should be able to rebuild the verdict from the page, which is the point of printing results rather than conclusions.
Batch-to-batch variation
The salt is made by fermenting glucose to gluconic acid, neutralising it with a magnesium source, then crystallising, drying and milling. Variation enters at each of those steps. Neutralisation and crystallisation shift the assay and the colour, the dryer shifts the water, and the mill shifts the sieve result.
Appearance is a soft line and a useful one. White to off-white tolerates a wide range, so movement inside it is not a rejection. A grey or yellow cast may follow a change of magnesium source or a dryer that ran hot, and the assay can still pass. The batch record answers that question faster than a colour chart.
Look at the direction of travel across several lots rather than at a single figure: magnesium creeping down, water creeping up, or a new absorption band in the infrared. The lot code should be the same on the certificate, the pack and the retained sample, or the trail stops at the laboratory door.
Outside testing, and when it earns its cost
A new source, a first consignment into a regulated market, a form under dispute, or a blend that behaves oddly: those are the occasions for an independent laboratory. The panel can be short. EDTA titration gives magnesium and the salt figure, infrared comparison gives the anion, Karl Fischer gives water, ICP-MS gives the metals, and a plate count gives the microbiology. Add diffraction when a second crystalline magnesium salt is plausible.
Every screen should come with a detection limit. Without one, “not detected” speaks about the reach of the method rather than the sample. Keep the chain of custody intact: the powder that was tested should be the powder that was retained, and the report should say which lot it belongs to.
If a result is disputed, the referee test worth paying for is the one that separates the two claims — a spectrum, a diffractogram, a water figure — not a second pass through the same titration.
Two suppliers, side by side
Six lines make the comparison: name and CAS number; assay and its basis; magnesium on the same lot; water; contaminants and microbiology; pack and lot code. Suppliers can match on assay while describing different powders, and the basis or the magnesium figure is usually where the difference shows.
Traceability is the second layer: who made the lot, which neutralisation and drying steps it went through, and which mill produced the mesh. The catalog specification is on the magnesium gluconate product page. The tests that separate this salt from its neighbours are on the identity page; the titration is described in the EDTA method note; how a lot is released is set out on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation