06 Identity & adulteration

How we prove a magnesium gluconate lot is the gluconate

Technical document 06 · Reviewed 2026-11-19 · Magnesium Gluconate

On this page
  1. Four questions, four kinds of evidence
  2. The 1:2 ratio and the arithmetic it fixes
  3. What diffraction contributes
  4. Substitutions and the trace each leaves
  5. Writing identity into the specification
  6. Five questions a buyer should ask

The elemental magnesium figure is shared property: magnesium oxide, magnesium citrate, magnesium lactate and magnesium sulfate all return it. A gluconate lot is established when several independent lines agree — the titration, the infrared spectrum, the water and, if needed, the diffraction pattern — and when the mole ratio behind those numbers matches the formula. That ratio is one magnesium to two gluconate ions, and the magnesium fraction it predicts is 5.86%.

In one line

A magnesium figure is the same measurement for every magnesium salt; the gluconate has to be proved by the anion, the water and the crystal.

Four questions, four kinds of evidence

Each layer answers something different, and each can fail on its own.

Identity evidence for magnesium gluconate
LayerQuestion it settlesEvidenceWhat it establishes
PaperworkIs a salt named at all?Name, CAS number, formulaA claim on a document
MetalHow much magnesium?EDTA titrationAmount, not which anion
AnionIs gluconate present?Infrared spectrum against a referenceThe gluconate part of the salt
Water and solid formAnhydrous? Any second phase?Karl Fischer; X-ray diffractionMass balance and crystal form

The titration is the strongest measure of quantity and the weakest test of identity; infrared is the mirror image, qualitative but difficult to satisfy with a different magnesium salt. Neither is sufficient alone.

The 1:2 ratio and the arithmetic it fixes

Gluconic acid has one acidic proton and magnesium has two charges, so two gluconate ions are needed per magnesium ion: Mg(C6H11O7)2, which is C12H22MgO14 at about 414.60 g/mol. Divide 24.305 by 414.60 and the magnesium fraction is 5.86%; the two gluconate ions account for the other 94.14%.

That single fraction ties the certificate together. If the assay is 98.0–102.0% of the salt, the magnesium must land between 5.74% and 5.98%. Pairing a 99% assay with a 5.5% magnesium figure breaks the arithmetic, and pairing a 97% assay with a 6.0% figure breaks it in the other direction. It takes a calculator and a minute.

The same arithmetic limits what can be hidden in the powder. Magnesium oxide is about 60.3% magnesium and magnesium sulfate heptahydrate about 9.9%, so a meaningful addition of either pushes the magnesium and the assay through their ceilings at the same time. About 2.6 g of oxide per kilogram of salt lifts the magnesium from the formula value to 6.0%, and the assay has already passed 102% before that point. A low-magnesium diluent such as glucose or maltodextrin is a different case: it pulls both figures down together, so the assay is what notices, not the ratio.

That is why the ratio is a first screen rather than a complete identity. It exposes a second magnesium salt and a plain dilution; it does not expose a non-magnesium diluent that has been balanced with a trace of oxide. The anion evidence closes that gap.

What diffraction contributes

X-ray diffraction identifies the crystalline phases in the powder. It separates the anhydrous gluconate from a crystalline second salt and shows whether the lot is crystalline at all. It does not measure purity and it says nothing about the counter-ion; it answers a question about the solid.

A statement that no crystalline magnesium oxide was found describes the method as much as the sample unless the detection limit and the preparation are given. Amorphous carriers scatter poorly and can be present without a clear pattern, so a tidy diffractogram is not proof that no maltodextrin is in the drum. Read it with the infrared spectrum and the water figure.

Diffraction is not a release test for this product. It earns its place for a new source, a disputed lot, or a blend that behaves unexpectedly on the press.

Substitutions and the trace each leaves

Substitutions, effects and the test that finds them
SubstitutionEffect on the figuresVisible signalTest
Glucose or maltodextrinAssay and magnesium fall togetherLow assay; water may climbAssay, infrared, mass balance
Magnesium oxideBoth figures riseAssay above 102%; oxide bandsAssay, infrared, diffraction
Magnesium sulfate or chlorideMagnesium rises; anion changesAssay ceiling; sulfate band; waterInfrared, diffraction, water
Gluconic acidAnion rises; magnesium fallsAcidic solution; low magnesiumpH, titration, infrared
Added waterAs-received assay fallsWater above 1.0%Karl Fischer

This salt is not an obvious target for substitution, since the material itself is not costly. The failures that do occur are a cheaper magnesium salt carried over into a blend, a sugar carrier used to reach a declared weight, and a wet lot offered against a dry specification. All three surface in the panel above.

Writing identity into the specification

  • “Magnesium gluconate, anhydrous, CAS 3632-91-5, C12H22MgO14.”
  • “Assay 98.0–102.0% by complexometric titration, with the basis stated.”
  • “Elemental magnesium 5.5–6.0% on the same lot, consistent with the assay.”
  • “Identification by infrared spectrum against a named reference, plus titration.”
  • “Water ≤1.0% by Karl Fischer; particle size ≥95% through 40 mesh.”
  • “No added magnesium oxide, magnesium sulfate, gluconic acid or carrier.”

Prohibitions bind exactly as ranges do. If the purchase document fixes a magnesium range and stays silent on added minerals, nothing has been excluded, and a supplier cannot be held to a rule the document never contained.

Five questions a buyer should ask

  1. Which reference spectrum did the infrared identity conform to, and can we see it?
  2. What are the assay and the elemental magnesium on this lot, and on which basis?
  3. What is the Karl Fischer water figure, and on what date was it measured?
  4. Is there a diffraction report, and which detection limit does it give?
  5. Was any magnesium salt, gluconic acid or carrier added after the reaction step?

Answers to those five amount to an identity file; a single assay percentage does not. The catalog specification is on the product page; the COA page shows where each figure sits; the grade page covers the powder choices; the FTIR method note and the XRD method note explain what each technique can see.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation