02 Grade comparison

Magnesium gluconate grades: mesh, granulation and water

Technical document 02 · Reviewed 2026-11-19 · Magnesium Gluconate

On this page
  1. One salt, several powders
  2. The catalog powder and the granulated option
  3. What the powder does before it is weighed
  4. The fill follows the magnesium figure
  5. What to write into the specification
  6. When a grade change is the wrong answer

Magnesium gluconate is a single salt, so a grade cannot change the chemistry: the catalog material is the anhydrous powder at 98.0–102.0% with 5.5–6.0% elemental magnesium, and it is offered as a 40 mesh powder or granulated on request. The grade decision is about the powder instead — mesh, flow, bulk density and water. Because the salt carries only 5.86% magnesium, every one of those decisions lands on the fill weight.

In one line

The salt is fixed; what a grade buys is particle size, flow and water, and those decide the fill, the dust and the tablet.

One salt, several powders

The magnesium figure is set by the formula, not by the grade. A granulated lot and the standard powder from the same batch hold the same percentage of magnesium, so no grade choice can raise the potency of the powder. What a grade changes is how the powder behaves on the line and how much of it fits into a capsule, a tablet die or a sachet.

Water is the one grade-like variable that does move the analysis. The material specified here is the anhydrous salt at water ≤1.0%, and a lot that picks up moisture behaves like a weaker material for the same drum weight: the assay on the as-received basis falls, the powder cakes, and the fill weight loses accuracy. A purchase order that says “magnesium gluconate powder” has named the chemistry and left the powder open.

The catalog powder and the granulated option

Grade attributes · standard powder against the granulated option
AttributePowder, 40 mesh (catalog)Granulated, on request
Particle size≥95% through 40 meshCoarser, defined by the granulation
Bulk densityLot-specific; ask for the measured figureUsually higher; ask for both figures
FlowAdequate for capsules; can bridge in a hopperMore uniform flow on a tablet press
DustDusty at transferLower dust at transfer
Tablet compressionNeeds a binder and a density checkThe usual starting point for tablets
Stick or sachet fillFills accurately; disperses quicklySlower to dissolve; check the mesh
Caking riskHigher in an open linerLower, but not removed
Specification statusThe catalog itemA separate specification, with any aid declared

The catalog fixes the mesh and says nothing about bulk density, so the density figure belongs in the quotation for the lot. Granulation is a separate specification rather than a packing choice: it changes the particle-size line and it may add a granulation aid, which has to be declared and may itself need a regulatory check.

What the powder does before it is weighed

Magnesium gluconate is freely soluble in water and gives a neutral solution, so solubility is not the grade question at this particle size. The powder is hygroscopic enough to cake under load in a humid store, and the 25 kg fiber drum has more headspace and a longer opening history than the 1 kg pouch. Keep the liner sealed, stand the drum off a concrete floor, and write down the opening date.

Bulk density decides whether the fill weight is achievable, and it varies with the crystallisation and the mill. Two lots that both pass 40 mesh can differ enough in density to change a capsule fill by a tenth. For tablets, density and flow together decide whether the press runs at speed or stops for punches; a granulated grade is the usual answer, and it should be trialled on the press rather than approved on paper.

Dust is a handling and hygiene issue as much as a yield issue. A finer powder suspends more readily at the weigh station, so local extraction and a closed transfer matter. Colour is white to off-white and is a weak signal on its own; a grey or yellow cast calls for the batch record rather than a grade decision.

The fill follows the magnesium figure

A 500 mg capsule fill of this salt carries about 29 mg of elemental magnesium. That single number explains why gluconate products are usually built around a moderate claim and why the grade and the fill have to be designed together.

Powder mass needed for an elemental magnesium claim, at 5.86% magnesium
Elemental magnesiumSalt massCapsules at 500 mg fillPractical format
25 mgAbout 425 mg1One capsule
50 mgAbout 855 mg2Two capsules or a small sachet
75 mgAbout 1,280 mg3Three capsules or a sachet
100 mgAbout 1,705 mg4Sachet, stick or a large tablet

The masses are calculated from the formula, so read them as planning figures. A lot at the bottom of the magnesium range, 5.5%, needs about 6.5% more powder for the same claim: 1,818 mg rather than 1,705 mg for 100 mg. The lot certificate, not the table above, is what the capsule machine or the press is set against.

A 100 mg claim is roughly 1.7 g of salt, which is four 500 mg capsules or a single sachet. A tablet of 1,000 mg is large by most consumers' standards and would deliver only about 59 mg of magnesium, so a high claim is not a realistic tablet for this salt. That is a property of the material, not a limitation of a particular grade.

What to write into the specification

  • “Magnesium gluconate, anhydrous, CAS 3632-91-5, C12H22MgO14.”
  • “Assay 98.0–102.0% by complexometric titration, with the basis stated.”
  • “Elemental magnesium 5.5–6.0% on the same lot; water ≤1.0% by Karl Fischer.”
  • “Identification by infrared spectrum and titration, against a named reference.”
  • “Particle size ≥95% through 40 mesh; bulk density reported for the lot, with the method.”
  • “Granulated or unmilled grade declared, with any processing aid named.”
  • “Heavy metals and microbiology as listed on the catalog specification.”

When a grade change is the wrong answer

Granulation fixes flow and dust; it does not fix a claim that is too high for the capsule. If the fill is the problem, the answer is the dosage form, the capsule size or a different magnesium source, not a coarser powder. A denser salt such as anhydrous magnesium citrate at about 16.2% magnesium or magnesium oxide at about 60% would cut the mass sharply, but each is a different label ingredient and a separate regulatory question.

If the problem is water rather than flow, a grade change does not help either. The pack and the store are the fix, and the stability page sets out how the powder behaves once the seal is broken.

The catalog specification sits on the product page. The magnesium figure against the lactate is compared on the gluconate versus lactate page; the release tests are on the COA page; bulk density is defined in the bulk-density entry; the storage question is on the stability page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation