How we prove a lot is ferrous bisglycinate
A lot is ferrous bisglycinate when five lines agree: the document names the chelate and CAS 20150-34-9; complexometric titration gives 26.0–28.0% iron; HPLC gives glycine at a 2:1 molar ratio to that iron; the iron is ferrous; and IR or XRD matches the reference solid. The iron figure alone cannot separate the chelate from a blend of an iron salt and glycine, and the assay alone cannot separate it from a dilution.
Iron content says how much iron is present; only the 2:1 glycine ratio, the ferrous state and the IR spectrum say it is the bisglycinate.
The identity layers
A certificate may carry the correct name and still leave the material unproven. Each layer answers a separate question; an answer to the first alone describes the paperwork, not the powder.
| Layer | What it establishes | Method | Evidence |
|---|---|---|---|
| Document | Is the identity stated? | Name, CAS number, formula | Paperwork only |
| Iron | How much iron is present? | Complexometric titration | The element, not the ligand |
| Ligand | Is the glycine ratio 2:1? | HPLC for glycine | The chelate stoichiometry |
| Valence | Is the iron ferrous? | Phenanthroline or potentiometric test | The oxidation state |
| Solid state | Is it a crystalline chelate? | IR and XRD | The compound, not a blend |
The glycine ratio: the stoichiometry check
At full stoichiometry the chelate is 27.38% iron and 73.61% glycine on a free-glycine basis, a mass ratio of 2.69 to 1 and a molar ratio of 2.00 to 1. The ratio is fixed by the formula, so a measured ratio that sits near 2.0 supports the chelate while a ratio near 1.7 points to a different composition.
Work the arithmetic on the certificate in front of you. A sample with 26.5% iron and 71.9% glycine gives (71.9 ÷ 75.07) ÷ (26.5 ÷ 55.845) = 2.02. The same iron figure with 58.0% glycine gives 1.63, which is what a blend with a large share of an iron salt looks like. The test is a ratio, not a threshold on either figure alone.
There is a limit to what the ratio can prove. The glycine assay must release the bound ligand — a hydrolysis step before HPLC — or it measures only free glycine. Even with total glycine, a blend of ferrous sulfate and free glycine can be built to land at 2:1, so the ratio has to be read with the sulfate test, the valence test and the IR or XRD pattern. Each one closes a gap the others leave open.
X-ray diffraction and the solid state
X-ray diffraction addresses the solid state: does the powder give a crystalline pattern that matches a reference, or is it amorphous? A crystalline chelate gives a pattern; a blend or a carrier-diluted powder usually does not give the same one. The comparison is most useful between two sources or two lots, where the chemistry is nominally the same.
XRD does not establish purity, and it says nothing about the counter-ion or the ligand. Before accepting a match statement, request the reference pattern and the method's detection limit. For a disputed lot, XRD plus the glycine ratio plus the iron and valence results is stronger than any one of them.
What adulteration looks like
| Substitution | Why it is used | Signal | Test |
|---|---|---|---|
| Ferrous sulfate plus glycine | Cheap iron salt with a ligand added | Sulfate present; IR or XRD does not match | Sulfate test, IR, XRD |
| Ferrous fumarate plus glycine | High iron figure at lower cost | Fumarate present; colour more orange | Fumarate by HPLC, IR |
| Ferric salt | Oxidised iron, lower cost | Ferric reaction; browner colour; lower solubility | Phenanthroline, solubility |
| Free glycine | Corrects the ratio of a blend | Ratio at or above 2:1 with low iron | Mass balance, iron, sulfate |
| Carrier dilution | Lowers iron per gram | Assay and iron low; LOD or ash high | Assay, iron, LOD, microscopy |
| EDTA or another chelate | Looks chelated on a generic test | Sodium present; no glycine; IR differs | ICP-OES sodium, HPLC, IR |
Colour is the weakest signal. Greenish-grey to off-white can be reproduced with a dye or a blend, and a genuine lot can darken with age. The stronger signals are the ratio, the valence, the sulfate and fumarate screens and the solid-state pattern.
How to write identity into the specification
- “Ferrous bisglycinate, CAS 20150-34-9, C4H8FeN2O4, 2:1 glycine–iron chelate.”
- “Assay 98.0–102.0% by HPLC; iron 26.0–28.0% by complexometric titration.”
- “Glycine ratio 2:1 molar; report the measured ratio and the calculation.”
- “Ferrous iron: report the ferrous/ferric ratio or a ferrous-specific test.”
- “IR conforms to the reference; XRD pattern available on request.”
- “Sulfate, fumarate and gluconate screened; no signal above the agreed limit.”
- “Sodium absent unless a sodium salt is declared.”
- “Loss on drying ≤5.0%; particle size ≥95% through 40 mesh.”
Five questions for the supplier
- Which chelate is this lot, and what CAS number appears on its certificate?
- What are the iron result and the glycine result, and what is their calculated molar ratio?
- Can you provide the IR spectrum and, if the solid state matters, an XRD pattern?
- What is the ferrous/ferric ratio, and which method was used to measure it?
- If this lot were disputed, would you re-test the retained sample jointly with us?
Those five answers, taken together, are the identity file. A single iron percentage does not. The catalog specification is published on the product page; the COA page maps each figure to its line on the certificate; the grade page covers the physical grades; the compliance page covers the destination file; the analytical methods are described in the methods library.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation