02.1 Dried vs heptahydrate

Dried ferrous sulfate vs heptahydrate: water, iron and the label

Technical document 02.1 · Reviewed 2026-11-20 · Ferrous Sulfate Dried

On this page
  1. Two articles, one salt
  2. Water of crystallisation
  3. The iron figure and the dose
  4. Fill weight, water activity and the blend
  5. The label names the article
  6. Choosing between them

By formula the heptahydrate, FeSO4·7H2O, is 20.09% iron and 45.36% water; the dried article is a partially dehydrated solid at 30.0–33.0% iron, with the water of crystallisation reduced to roughly one to two molecules per ferrous sulfate. The same 20 mg iron dose is about 99.6 mg of heptahydrate or 60.6–66.7 mg of dried article, so the switch changes the fill weight, the water load and the ingredient name on the label.

In one line

The difference is water: about 45% in the heptahydrate and roughly 10–18% in the dried article, which is why the same iron dose weighs a third to two-fifths less.

Two articles, one salt

The two articles share the same salt; what differs is the amount of water locked into the crystal. The heptahydrate has seven molecules of water per ferrous sulfate. Drying removes most of that water but not all of it: the commercial article is nominally the monohydrate and in practice a mixture of hydrates.

Three articles are often confused: the heptahydrate, the dried article and the anhydrous salt. The anhydrous salt carries no crystal water and takes up moisture most readily. This page compares the first two, because they are the two that appear on supplement labels and in purchase orders.

The hydrate belongs to the article identity; it is not a purity grade. A certificate that says only “ferrous sulfate” has not identified the article. The iron and water figures are what separate them.

Water of crystallisation

The formula water is fixed: 45.36% for the heptahydrate and 10.60% for the monohydrate. The commercial dried article sits across a window. At 33.0% Fe the powder is close to the monohydrate and carries about 10.2% water; at 30.0% Fe it carries about 18.4% water, because more hydrated forms are present. The 30.0–33.0% iron window is therefore also a water window.

Iron and water in the heptahydrate and the dried article
ArticleIronWaterMass for 20 mg Fe
Heptahydrate20.09% by formula45.36% by formulaAbout 99.6 mg
Dried, nominal monohydrate32.87% by formula10.60% by formulaAbout 60.9 mg
Dried, at the 30.0% iron edge30.0%About 18.4%About 66.7 mg
Dried, at the 33.0% iron edge33.0%About 10.2%About 60.6 mg

The loss-on-drying line on the certificate is not automatically a total-water figure. The monohydrate's bound water is part of the crystal, and a loss-on-drying result depends on the test conditions. If total water is the specification, ask for Karl Fischer and state the method. The iron figure is the practical control on the hydrate: it moves as the water moves.

Water per dose follows the same split: about 45 mg with the heptahydrate at 20 mg of iron, against roughly 6–12 mg with the dried article. That is the water the capsule, tablet or blend has to tolerate. It is also why the dried article is chosen for a tight fill or a moisture-sensitive matrix, and why the heptahydrate is chosen when water in the crystal is acceptable.

The iron figure and the dose

The iron figures are 20.09% and 30.0–33.0%. The mass per dose is the reciprocal: 20 mg ÷ 0.2009 = 99.6 mg; 20 mg ÷ 0.330 = 60.6 mg; 20 mg ÷ 0.300 = 66.7 mg. At 40 mg the range is 121.2–133.3 mg for the dried article and 199.2 mg for the heptahydrate. A kilogram carries about 201 g of iron as the heptahydrate and 300–330 g as the dried article.

These are calculated figures; the batch certificate's iron result takes the place of the theoretical number, and the batch record should say which figure was used. A formula written for 31% iron under-delivers by about 3% if the lot assays 30.0%, and over-delivers by about 6% if the lot assays 33.0% and the formula still weighs for 31%. The window is wide enough that the weigh-up has to use the lot result, not the midpoint.

The label declares elemental iron while the order is placed in salt weight. The iron figure is the only bridge between them.

Fill weight, water activity and the blend

For a capsule, the dried article puts 20 mg of iron into about 60.6–66.7 mg of powder; the heptahydrate needs about 97.6–102.6 mg at its catalog window. At 40 mg of iron the difference is about 121–133 mg against about 195–205 mg, enough to change the shell size or the excipient load.

In a tablet, the heptahydrate's water becomes part of the granulation: it can be useful in a wet process, unwelcome in a dry one, and it can react with alkaline excipients. The dried article carries less water, but it is still acidic and hygroscopic; it is not an inert filler.

In a blend, the share of the formula changes: 20 mg of iron is about 6.1–6.7% of a 1 g stick pack as dried article and about 9.8–10.3% as heptahydrate. That changes flow, segregation and taste. The 80 mesh powder is the standard form; granulation is a separate specification.

The label names the article

The label has to name the article that was weighed. In the EU, the ingredient list carries the iron source and the nutrition declaration shows iron in mg against the 14 mg reference intake. In the US, the Supplement Facts panel shows elemental iron in mg and its share of the 18 mg Daily Value, with the source beside it in the ingredient list. A solid oral supplement that contains iron also carries the required accidental-overdose warning.

A label that says only “ferrous sulfate” is ambiguous. The hydrate is part of the ingredient identity, so a switch without a label change would name a different article. The dose declaration also has to match the weigh-up: 20 mg of iron assumes about 60.6–66.7 mg of dried article or about 99.6 mg of heptahydrate.

No disease claim is made for either article. The label and any claim are reviewed separately for the destination.

Choosing between them

A solution, a syrup or a process built on a freely soluble crystal points to the heptahydrate. A capsule, a tablet or a dry blend with a tight fill, a high iron dose or a moisture-sensitive matrix points to the dried article.

They are separate articles, not interchangeable weights. A formula written for 31% iron and weighed with heptahydrate at the same mass under-delivers iron by about 35%. A label naming the heptahydrate is not met by the dried article. Either direction of switch needs change control, a new specification and a fresh label check.

The catalog data are on the dried ferrous sulfate product page; the grades page sets the choice beside the physical forms; the heptahydrate page covers the other article; the compliance page covers the label route; the COA page shows how the iron figure is reported.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation