01 COA & batch testing

What the COA for ferrous fumarate actually contains

Technical document 01 · Reviewed 2026-11-19 · Ferrous Fumarate

On this page
  1. The certificate as a test report
  2. Dried basis on an anhydrous salt
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a ferrous fumarate lot reports appearance, identification by infrared spectrum and titration, assay as C4H2FeO4 at 97.0–101.0%, iron at 31.0–33.0%, loss on drying, particle size, heavy metals and microbiology. Both percentages sit on the dried basis, so the moisture result is part of the assay rather than a separate note. The ranges are the catalog specification; a batch certificate is the evidence for a specific pack.

In one line

The assay and the iron figure describe one salt from two directions; without the loss on drying beside them, neither percentage has a basis.

The certificate as a test report

Each row should be repeatable by a second laboratory: the parameter, the method and the release limit, with the header naming the salt, CAS number, lot code, pack size and specification edition. A bare “conforms” records a judgement, not the evidence for it.

The identity row is the one that separates ferrous fumarate from another red iron powder. The assay and iron rows then say how much of the salt is present. Read them together, because the ratio between them is a check on the formula.

Identity, assay, moisture and contaminants · ferrous fumarate
ParameterMethodRelease limit
AppearanceVisualOrange-red to reddish-brown powder
IdentificationInfrared spectrum and titrationConforms to reference
Assay (C4H2FeO4, dried basis)Complexometric titration97.0–101.0%
Iron (Fe), dried basisComplexometric titration31.0–33.0%
Loss on dryingGravimetric≤2.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Dried basis on an anhydrous salt

Ferrous fumarate is anhydrous: C4H2FeO4, 169.90 g/mol, with no water of crystallisation. The ≤2.0% loss-on-drying limit therefore covers surface moisture rather than a hydrate shell. The dried-basis correction is small, but it is not optional. A lot reading 97.4% as-is with 1.6% loss calculates to 98.98% on the dried basis; an iron result of 31.7% as-is becomes 32.2%.

The formula sets the expected ratio. Iron is 55.845 ÷ 169.90 = 32.87% of the molecule by mass, so iron divided by assay should sit near 0.329. A lot at 99.0% assay and 32.5% iron is consistent with the salt. A lot at 99.0% assay and 31.0% iron passes both release windows, but the ratio is 0.313; that is a question for the supplier, not a result to average away.

Unlike ferrous sulfate heptahydrate, which carries about 45% water of crystallisation, this salt has no hydrate water; a high loss on drying is surface water or a wet pack.

Release limit versus batch result

A limit is a boundary; a result is a measurement. Both belong on the page, in separate columns, with the method beside them. A column that repeats the specification range has recorded the boundary, not the lot.

What the result column should contain
ParameterRelease limitResult column
Assay97.0–101.0% dried basisA measured percentage with the method and the basis
Iron31.0–33.0% dried basisA measured percentage; the ratio to assay checked
Loss on drying≤2.0%A measured percentage and the conditions used
Heavy metalsPer elementA figure in mg/kg for each element, with the detection limit
Particle size≥95% through 40 meshThe measured percentage through the sieve

Identity lines are the exception: a comparison can legitimately report “conforms”, provided the certificate names the reference and the edition. The contaminant lines cannot. A “Pb: <3 mg/kg” entry describes the method's sensitivity; an actual figure describes the lot. Ask for the number.

The oxidation state is the usual gap. Complexometric titration measures iron, and the catalog names it without saying whether the titre was run on ferrous iron or on total iron after reduction. If the certificate cannot answer that, ask for a ferrous-specific result or an agreed ferric limit beside it. The identity page sets out the difference.

What moves between batches

The reaction, the drying step and the milling move different lines. Drying drives the loss on drying; milling and sieving move the 40 mesh result; the reaction and the washing move residual acidity and the free-fumaric-acid figure. A change of sieve can change the powder's flow without changing the chemistry.

Colour is the least quantitative line and often the earliest signal. A batch that is noticeably darker or browner than the catalog description can carry a ferric fraction or an iron oxide contaminant while the assay still passes. Pull the batch record and the ferrous result before rejecting on appearance alone.

Look for a trend, not a single result near an edge: iron drifting low against a stable assay, or loss on drying climbing. Certificate, pack and retained sample should carry the same lot code.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a label that names ferrous fumarate, or a disputed result. The useful panel is not a repeat of the certificate. It is infrared identity, complexometric iron, a ferrous-specific titration or total iron by ICP-OES for the ferric difference, loss on drying, the heavy-metal panel by ICP-MS, microbiology, and sieve analysis.

Add X-ray diffraction if a crystalline iron oxide or another salt is suspected, and an HPLC check on the fumarate if the free acid is the question. Ask the laboratory to report its detection limit and basis for every line. A “not detected” without a limit is evidence about the method, not the sample.

When a result is contested, send the retained sample, the supplier's certificate and the specification to the referee, and ask for tests that separate the forms rather than a repeat assay.

What to compare between suppliers

Six lines to compare between two ferrous fumarate certificates
LineWhat to askWhy it matters
Form and CASAnhydrous ferrous fumarate, CAS 141-01-5The salt name and the formula set the iron figure
Assay and ironBoth results on the dried basis, with methodsThe ratio is a check on the salt
Loss on dryingResult and conditionsDefines the basis and predicts caking
Oxidation stateFerrous result or a ferric limitTotal iron does not show Fe(II)
Particle sizeMesh and percentage passingFlow, dust and fill weight
TraceabilityLot code on certificate, pack and retained sampleAn accurate certificate can cover another drum

If two offers agree on iron but not on the basis or the oxidation state, they are not offers for the same material. The catalog specification sits on the product page; the fumarate versus sulfate page takes the salt comparison further; the methods library describes the titration and ICP techniques; the quality page shows the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation