06 Identity & adulteration

How we prove a ferrous fumarate lot is the ferrous salt

Technical document 06 · Reviewed 2026-11-19 · Ferrous Fumarate

On this page
  1. Four layers, four different failures
  2. The 1:1 ratio and the iron figure
  3. What X-ray diffraction adds
  4. The substitutions that move one number at a time
  5. How to write the identity into the specification
  6. Five questions for the supplier

A ferrous fumarate lot is the named salt when four lines agree: the document names C4H2FeO4 and CAS 141-01-5; the infrared spectrum matches a reference; iron sits at 31.0–33.0% against the 32.87% the formula predicts; and the condition tests close the mass balance. An iron percentage alone cannot separate the fumarate from another red iron powder, and it cannot show whether the iron is still ferrous.

In one line

Identity is the ratio as much as the number: one ferrous ion per fumarate, 32.87% iron by formula, confirmed by IR and a mass balance.

Four layers, four different failures

Each layer answers a different question, and a certificate that fills only one of them has not proved the material. The document can be right while the powder is wrong; the spectrum can match while the lot is diluted; the iron figure can be high while the iron is ferric. The layers are separate on purpose.

Identity layers: what each test establishes
LayerTestWhat it establishesWhat it leaves open
DocumentName, formula, CAS, hydrate stateThe file is about the right moleculeNothing about the powder
Chemical identityInfrared spectrum against a referenceThe fumarate ligand is presentNot a quantity, not the oxidation state
Iron ratioIron and assay on the dried basisThe iron-to-fumarate proportionBlind to ferric iron if the method is total iron
ConditionLoss on drying, mesh, metals, microbiologyFitness for the specificationNo proof of identity

The document layer is not paperwork for its own sake. Ferrous fumarate is anhydrous, so a certificate that describes a hydrate, or that gives a molecular weight for a hydrated form, has described a different material. The CAS number and the formula should match the specification before any instrument is used.

The 1:1 ratio and the iron figure

Ferrous fumarate is one ferrous ion bound to one fumarate dianion: C4H2FeO4, 169.90 g/mol. Iron is 55.845 ÷ 169.90 = 32.87% of that mass, and the fumarate part is the remaining 67.13%. The ratio is fixed by the formula, so the two release lines are not independent: iron divided by assay should sit near 0.329.

That ratio is a diagnostic. A lot with 99.0% assay and 32.5% iron is consistent with the salt. A lot with 99.0% assay and 31.0% iron passes both windows, but the ratio is 0.313, which suggests a diluent, a wet lot or an iron salt with a different anion. A lot with 99.0% assay and 34.0% iron points the other way, towards an iron oxide or a ferric phase that the titration counts as iron but the fumarate does not account for.

The oxidation state needs its own measurement. Complexometric titration gives an iron figure, and unless the method is written to preserve or reduce a specific state, it is a total-iron result. A ferrous-specific redox titration, or total iron by ICP-OES beside a ferrous result, separates Fe(II) from Fe(III). The difference is the ferric fraction, and it is the number that explains a dark colour.

A free-fumaric-acid check by HPLC adds the other side of the balance. An excess of free acid, or a fumarate figure that does not match the iron, points to a blend or a reaction that did not go to completion. Ask for the chromatogram if the number is near a limit.

What X-ray diffraction adds

Ferrous fumarate is a crystalline, anhydrous solid, and X-ray diffraction reads its lattice. A pattern that matches a reference confirms the crystalline phase; a pattern with extra lines can show a crystalline impurity such as an iron oxide, a ferric phase or an inorganic diluent. It can also distinguish the fumarate from ferrous sulfate heptahydrate, which has its own hydrate lattice and a very different iron figure.

XRD is not a routine release test here. A certificate that states “XRD conforms” but names no reference has told the reader very little. Ask for the reference pattern, the sample preparation and the detection limit. The method is most useful when the question is solid form or a suspected crystalline contaminant, not when the question is assay.

Infrared and XRD are complementary. IR identifies the organic ligand through its carboxylate bands; XRD identifies the crystal phase. Neither measures iron, and neither replaces the ratio calculation.

The substitutions that move one number at a time

Adulteration routes for ferrous fumarate and the tests that show them
RouteWhat movesTest that shows it
Ferrous sulfate or another ferrous saltIron may pass; sulfate, LOD and IR changeInfrared, sulfate, loss on drying
Iron oxide or a ferric powderTotal iron rises; ferrous iron does notFerrous against total iron, XRD
Diluent such as dextrose or maltodextrinAssay and iron fall together; IR changesAssay, IR, loss on drying
Dye matched to the orange-red colourColour matches; the spectrum does notInfrared, HPLC
Water on the surfaceAs-is iron drops while the dried figure holdsLoss on drying next to the assay

The pattern to watch is a pair that no longer moves together. Total iron above the ferrous figure suggests an added ferric or elemental source; ferrous iron below a normal total suggests oxidation; iron below the assay with a raised loss on drying suggests water or a diluent.

A blend is legitimate when it is declared: the label names both iron sources and the certificate reports each contribution. The defect is the undisclosed blend, not the blend.

How to write the identity into the specification

  • “Ferrous fumarate, anhydrous, C4H2FeO4, CAS 141-01-5.”
  • “Identification by infrared spectrum against a named reference.”
  • “Assay 97.0–101.0% and iron 31.0–33.0%, both on the dried basis; loss on drying ≤2.0%.”
  • “Report whether iron is ferrous or total; state the method and the ferric result where agreed.”
  • “Free fumaric acid by HPLC reported; ≥95% through 40 mesh.”
  • “Free of added ferric salt, iron oxide and diluent; contaminants and micro as the catalog.”

Written this way, the specification tells the laboratory what to measure and the supplier what will fail. “Iron 32%” alone does neither.

Five questions for the supplier

  1. Is the iron result ferrous iron or total iron, and which method and basis are reported?
  2. What is the assay, and does iron divided by assay sit near the 0.329 the formula predicts?
  3. Does the infrared spectrum match a named reference, and can the spectrum be provided?
  4. What are the loss on drying, particle-size and free-fumaric-acid results for this lot?
  5. Who produced the lot, and does the batch record connect to the same code as the retained sample?

Those five answers, taken together, are the identity file. Start at the product hub for the catalog specification, then compare the certificate lines on the COA page and the particle options on the grade page. The ferrous sulfate page covers the salt a substitution would most likely involve, and the methods library explains the IR, XRD and titration techniques.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation