Ferrous fumarate grades: powder, mesh and the salt choice
The catalog grade is an anhydrous ferrous fumarate powder with at least 95% passing 40 mesh, and a granulated form is available on request. Those are process variants of one molecule. The larger decision is the salt: at 31.0–33.0% iron the fumarate carries about 60% more iron per gram than ferrous sulfate heptahydrate, so the choice changes the fill, the colour and the ingredient line.
The mesh decides how the powder runs; the salt decides how much iron each gram carries and what the label may name.
A grade is a process variant, not a new salt
Buyers use “grade” for several different things: mesh, granulation, assay, and sometimes the salt itself. On this page a grade is a variation on ferrous fumarate: the same C4H2FeO4, the same CAS 141-01-5, the same 31.0–33.0% iron, with a different particle-size profile or a granulation step. A different salt is a different material with its own iron figure.
The distinction matters on the purchase order. “Iron 32%” does not name a salt; “ferrous fumarate, 40 mesh” does. A supplier can meet the first with a ferrous sulfate blend, a ferric compound or a diluted powder, and the label would then be wrong.
The iron sources around it
| Source | Iron form | Elemental Fe | In water | What it changes |
|---|---|---|---|---|
| Ferrous fumarate | Fe(II) salt | 31.0–33.0% | Practically insoluble | Compact fill; suspension; orange-red colour |
| Ferrous sulfate heptahydrate | Fe(II) salt | 19.5–20.5% | Freely soluble | Larger mass; acidic solution; pale blue-green |
| Ferrous gluconate dihydrate | Fe(II) salt | 11.8–12.5% | Soluble | Largest mass; acidic solution |
| Ferrous bisglycinate | Fe(II) chelate | About 20–23% | Soluble | Chelate identity; different tests |
| Ferric pyrophosphate | Fe(III) salt | 24.0–26.0% | Practically insoluble | Ferric state; pale colour |
Read the table as a map of the options; the lot certificate supplies the figure for the weigh-up. The rows are not a ranking, because each source fits a different dosage form, label and process.
40 mesh, colour and flow
The 40 mesh line corresponds to an aperture of about 425 µm, and ≥95% passing leaves a coarse tail of up to 5%. Two lots that both pass can behave differently: one at 95.1% has more coarse particles than one at 99.9%, and flow, dust and blend uniformity follow that tail. Ask for the actual percentage, not only the pass statement.
Ferrous fumarate is practically insoluble in water and dissolves in dilute acid. That is a formulation fact: a tablet or capsule can carry it as a solid, and a suspension needs a dispersion step and a check for settling. A clear drink is not its natural home.
Colour runs from orange-red to reddish-brown. The window is wide, and a granulated lot can look different from a milled one without any chemical change. A dull or brown cast is a prompt to check the iron and the ferric figure, not a grade difference.
Granulation is available on request. It improves flow and reduces dust, and it adds a process step and a granulating aid that may need to be declared. The iron figure and the assay stay the same; the particle-size line and the lead time move.
The grade and the fill
A label claim is written in elemental iron, while the weigh-up is in salt. At the catalog midpoint, 1 mg of iron takes about 3.1 mg of ferrous fumarate or about 5.0 mg of the sulfate heptahydrate. That difference is the fill.
| Iron claim | Ferrous fumarate 31.0–33.0% | Ferrous sulfate 19.5–20.5% |
|---|---|---|
| 14 mg | 42–45 mg | 68–72 mg |
| 18 mg | 55–58 mg | 88–92 mg |
| 20 mg | 61–65 mg | 98–103 mg |
| 30 mg | 91–97 mg | 146–154 mg |
A 500 mg fill of ferrous fumarate carries 155–165 mg of iron, which is far more than most single-dose claims and leaves room for other actives. The same fill of sulfate carries 98–103 mg. The arithmetic is not a recommendation; it is how the capsule size and the number of units follow from the claim.
Compression adds another question. A fine powder may need granulation to run on a tablet press, and the granulating aid then belongs in the ingredient list. A capsule can take the milled powder directly, though dust and static matter at the filling station.
How to write the grade into the specification
- “Ferrous fumarate, anhydrous, C4H2FeO4, CAS 141-01-5.”
- “Assay 97.0–101.0% on the dried basis; iron 31.0–33.0% on the dried basis.”
- “Identification by infrared spectrum and titration against a named reference.”
- “Loss on drying ≤2.0%; ≥95% through 40 mesh.”
- “Powder, 40 mesh; granulated on request, with the granulating aid declared.”
- “Heavy metals and microbiology as the catalog; ferric figure or ferrous-specific result agreed separately.”
Name the mesh and the granulation, not only the salt. The same ferrous fumarate at a different particle size is a different handling experience, and a tablet line and a capsule line rarely want the same powder.
When fumarate is the wrong grade
It is the wrong choice when the formula needs a clear solution: the salt is practically insoluble, and no mesh makes it dissolve. It is wrong when the label names another iron source, because the ingredient line and the identity tests change with the salt. It is also a poor fit for a pale product where the orange-red colour would show through a translucent shell or a light powder blend.
In those cases the answer is a different specification: ferrous sulfate when a soluble acidic salt fits, ferric pyrophosphate when a pale ferric source is wanted, or a chelate when the label names one. The fumarate versus sulfate page works through the two-salt comparison.
The catalog line is on the ferrous fumarate product page. The COA page shows the assay and moisture lines; the ferrous sulfate page carries the soluble alternative; the iron pyrophosphate page covers the ferric option; the methods library explains the tests.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation