06 Identity & adulteration

How to prove a lot is dicalcium phosphate

Technical document 06 · Reviewed 2026-11-19 · Dicalcium Phosphate

On this page
  1. Four layers, four questions
  2. The calcium-to-phosphorus ratio
  3. X-ray diffraction and the hydrate
  4. Where the substitutes show up
  5. Identity clauses for the specification
  6. Five questions to put to the supplier

Dicalcium phosphate is identified by agreement between four results: the document, the calcium titration, the phosphorus determination and the diffraction pattern. The document names CaHPO₄ and the hydrate; the titration gives calcium; the spectrophotometric method gives phosphorus; the diffractogram shows monetite or brushite. Calcium alone cannot separate dicalcium phosphate from calcium sulfate, which carries about the same calcium percentage. The phosphorus figure and the ratio close that gap.

In one line

Calcium proves the element, phosphorus proves the anion, and the ratio plus the diffraction pattern proves which calcium phosphate, and which hydrate, the lot is.

Four layers, four questions

A certificate can carry the right name and still leave the material unproven. The layers below ask separate questions, and each needs its own evidence. An answer to the first alone describes the paperwork, not the powder.

Four layers of dicalcium phosphate identity
LayerQuestionTestWhat it proves
DocumentAre the formula, CAS number and hydrate named?Specification and labelPaperwork only
CalciumIs the calcium figure right?Complexometric titration with EDTAThe element, not the salt
PhosphorusIs the anion phosphate?Spectrophotometry after acid digestionThe phosphate anion
RatioIs the calcium-to-phosphorus balance that of CaHPO₄?Calculation from the two resultsWhich calcium phosphate
Solid stateWhich hydrate and crystal form are present?X-ray diffractionMonetite, brushite or a second phase

Acid-insoluble matter is a useful negative check beside these: it measures what the acid did not dissolve, and a high residue points to silica, a silicate or a dirty source. It does not identify the salt, but it caps how much of the powder can be something else.

The calcium-to-phosphorus ratio

Pure CaHPO₄ is 29.46% calcium and 22.76% phosphorus, a mass ratio of 1.29 to one. The ratio is the most portable identity check because it needs only the two results the certificate already carries. A lot at 29.5% calcium and 22.4% phosphorus has a phosphorus-to-calcium ratio of 0.759 against the theoretical 0.773, which is within the normal spread. A lot at 29.5% calcium and 15.2% phosphorus has a ratio of 0.515, which is the ratio of tricalcium phosphate, and the certificate has described a blend rather than the ordered salt.

The ratio distinguishes the salt, not the hydrate. Anhydrous dicalcium phosphate and the dihydrate have the same 1.29 ratio, because the water of crystallisation adds mass to both the calcium and the phosphorus denominator without changing their proportion. The hydrate needs the loss on drying or the diffraction pattern; the ratio cannot answer that question.

Two common substitutes sit outside the ratio window. Calcium sulfate carries about 29.4% calcium and no phosphorus, so a calcium-only specification passes it. Calcium carbonate carries about 40% calcium and no phosphorus, so it fails on both figures and shows an acid effervescence. Monocalcium phosphate carries about 17% calcium and 26.5% phosphorus, a phosphorus-to-calcium ratio of 1.55, going the other way. Each of those is visible in the pair of figures, and none of them is visible in the calcium figure alone.

X-ray diffraction and the hydrate

Dicalcium phosphate crystallises as monetite in the anhydrous form and as brushite in the dihydrate. Monetite and brushite scatter X-rays differently, so a scan can name the hydrate and show whether a second crystalline phase is present. Tricalcium phosphate gives a different pattern again, usually described as whitlockite or an apatitic phase depending on the preparation, so the same scan can separate the two salts.

Diffraction answers a question about the solid, not about purity. It can show monetite where brushite was expected, or a tricalcium phosphate phase above the detection limit. It cannot quantify an amorphous fraction, and it cannot see a substitution that leaves the crystal structure unchanged. Before accepting a “match” statement, ask for the reference pattern, the scan range and the detection limit.

The hydrate matters commercially because the calcium and phosphorus per gram depend on it. A lot sold as anhydrous at 29.46% calcium is the anhydrous salt; the same powder after taking up two waters of crystallisation reads about 23.29% calcium. The diffraction pattern and the loss on drying are the two independent ways to see that change.

Where the substitutes show up

Substitutions and the signals that expose them
SubstituteWhat it doesSignalTest
Calcium sulfateMatches the calcium figure; adds no phosphorusPhosphorus near zero; sulfate test positivePhosphorus, sulfate test, XRD
Calcium carbonateRaises calcium; adds no phosphorusEffervescence in acid; carbonate presentAcid reaction, phosphorus, XRD
Tricalcium phosphateRaises calcium; lowers the ratioCalcium high, phosphorus ratio near 0.52Ratio, XRD
Monocalcium phosphateLowers calcium; raises the ratioAcidic solution; phosphorus high against calciumRatio, pH, XRD
Silica or silicateDilutes both figures; adds residueAcid-insoluble matter highAcid-insoluble matter, XRD
Feed-grade materialSame chemistry, different contaminant panelFluoride or heavy metals outside the food limitFluoride, ICP-MS, documentation

Colour tells you least. Both hydrates are white, and an off-white tone usually reflects the lime source or the drying step. The phosphorus figure, the ratio, the acid-insoluble residue and the diffraction pattern carry the evidence. A certificate with calcium and assay but no phosphorus has not tested the substitution that matters most.

Identity clauses for the specification

  • “Dicalcium phosphate, anhydrous, CAS 7757-93-9, CaHPO₄; hydrate declared.”
  • “Assay 98.0–102.0% as CaHPO₄; calcium 29.0–30.0%; phosphorus 22.0–23.5%.”
  • “Identification by infrared and by the calcium and phosphate reactions.”
  • “Calcium-to-phosphorus ratio calculated from the two results and reported with them.”
  • “Loss on drying ≤2.0%; X-ray diffraction when the hydrate or a second phase is in question.”
  • “No calcium sulfate, calcium carbonate, tricalcium phosphate, monocalcium phosphate or silica added.”
  • “Hydrate and crystal form under change control; lot code on the pack and the certificate.”

The exclusion clause carries as much weight as the positive lines. Without an exclusion for sulfate and carbonate, a blend can sit inside the calcium window; the clause gives the laboratory a line to test.

Five questions to put to the supplier

  1. Is this lot the anhydrous salt or the dihydrate, and what water figure does the certificate report?
  2. What are the calcium and phosphorus results, and were both measured on the same lot and basis?
  3. What is the calculated calcium-to-phosphorus ratio, and does it match CaHPO₄?
  4. Which phase does X-ray diffraction show, and against which reference pattern?
  5. What is the fluoride figure, and will you re-test the retained sample jointly if a result is disputed?

Those five answers build an identity file; a calcium percentage on its own does not. The product hub carries the catalog specification; the COA page shows which certificate line carries each figure; the grade page compares the hydrates; the dicalcium versus tricalcium page takes the ratio arithmetic further; the calcium carbonate page describes the carbonate that would show up as a phosphorus gap; the methods index explains the tests.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation