Anhydrous or dihydrate: choosing a dicalcium phosphate grade
Dicalcium phosphate is sold as the anhydrous salt (CAS 7757-93-9) and as the dihydrate (CAS 7789-77-7), and the two are different specifications, not two names for one powder. The anhydrous salt is 29.46% calcium and 22.76% phosphorus by formula; the dihydrate is 23.29% calcium and 18.00% phosphorus and carries about 21% water of crystallisation. The grade decision is the hydrate first, then the particle form.
The hydrate is the grade: it sets the calcium and phosphorus per gram and the water the powder carries, while the particle form decides how it runs on a press.
Why one formula comes in two hydrates
Dicalcium phosphate is made by reacting a calcium source with phosphoric acid and drying the precipitate. The drying step decides the solid phase. Dried to remove the water of crystallisation, the product is the anhydrous salt, CaHPO₄. Dried under milder conditions, the product is the dihydrate, CaHPO₄·2H₂O. Both are the same calcium-to-phosphorus compound, and both are practically insoluble in water, but they are not interchangeable by mass.
The hydrate also changes the commercial grade. A powder intended for direct compression needs a defined particle distribution, a bulk density and a flow that the standard powder does not have, so suppliers offer a granulated or a compaction-grade form. That form is a physical grade of the same chemistry, and it should be named in the purchase specification alongside the hydrate.
The catalog material is the anhydrous powder at ≥95% through 40 mesh. The dihydrate and the granulated form are the alternatives to compare against it, and each one changes the label arithmetic.
The forms side by side
| Property | Anhydrous | Dihydrate | Granulated |
|---|---|---|---|
| Formula | CaHPO₄ | CaHPO₄·2H₂O | CaHPO₄, agglomerated |
| CAS number | 7757-93-9 | 7789-77-7 | Same as the base salt |
| Calcium | 29.46% theoretical | 23.29% theoretical | Unchanged by granulation |
| Phosphorus | 22.76% theoretical | 18.00% theoretical | Unchanged by granulation |
| Water of crystallisation | None | About 21% by mass | None or 21%, per base |
| Loss on drying | ≤2.0% | Reports the hydrate water | Depends on the base and the binder |
| Particle form | Powder, 40 mesh | Powder or granule | Coarse, free-flowing |
| Usual fit | Dry blends, capsules, tablets | Wet granulation, some tablets | High-speed tableting |
The water figure is the line that separates the first two columns. A certificate that reports 20% loss on ignition for a material ordered as anhydrous is describing the dihydrate, whatever the label on the drum says. The granulated column is not a third chemistry; it is a physical form of one of the first two, and the specification should say which.
Particle, density and the tablet press
The catalog fixes one physical line: ≥95% through 40 mesh. Bulk density, tapped density, flow and compressibility are not on that list, and they are the properties that decide whether the powder can be filled at speed. A standard powder can run in a capsule or a simple blend; a direct-compression tablet needs a denser, freer-flowing grade, and the supplier should provide the density and the flow data for the lot.
The anhydrous salt is the safer base for a moisture-sensitive tablet. The dihydrate carries water in the crystal, and heat can drive it off; a drying step or a hot granulation can change the phase and release water into the blend. That is not a defect in the dihydrate, but it is a reason to match the hydrate to the process rather than to convenience.
Dicalcium phosphate is abrasive enough to matter to tooling, and its flow and compaction behaviour change with the particle form. The press trial should run the grade that will be bought, not a sample of a different density.
Dose arithmetic and the label
Calcium is the figure the label declares, so the salt weight follows from the calcium content. A 500 mg calcium dose needs 1.70 g of the anhydrous salt (500 ÷ 0.2946) or 2.15 g of the dihydrate (500 ÷ 0.2329). A 1,000 mg dose needs 3.39 g or 4.30 g. The hydrate changes the mass in the capsule, not the calcium.
Phosphorus comes along at a fixed ratio. One mole of calcium carries one mole of phosphorus, so 500 mg of calcium brings about 386 mg of phosphorus from either hydrate, and 1,000 mg of calcium brings about 773 mg. The dihydrate does not dilute the ratio; it only adds water to the weight. That is why the hydrate must be declared before the dosage form is sized, and why a formula that needs a low phosphorus load has to change salt rather than change hydrate.
The label arithmetic has one more step. If the supplement facts panel declares calcium, the figure is elemental calcium, not the weight of the salt. The ingredient statement names the salt; the nutrient panel names the element. A formula that confuses the two will overstate or understate the dose by about a third.
What to write into the specification
- “Dicalcium phosphate, anhydrous [or dihydrate], CAS 7757-93-9 [or 7789-77-7], CaHPO₄.”
- “Assay 98.0–102.0% as CaHPO₄; calcium 29.0–30.0%; phosphorus 22.0–23.5%.”
- “Loss on drying ≤2.0% for the anhydrous grade; state the hydrate and the water figure for the dihydrate.”
- “Particle size ≥95% through 40 mesh; bulk density and flow if the powder is to be compressed.”
- “Heavy metals Pb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 mg/kg; microbiology as listed; fluoride if the destination requires it.”
- “No calcium carbonate, calcium sulfate, tricalcium phosphate or silica added.”
- “Hydrate, particle form and manufacturer under change control.”
The negative clause matters because calcium sulfate carries about 29.4% calcium, the same figure as dicalcium phosphate. A specification that tests calcium only will not see the substitution; the phosphorus line and the ratio are what see it.
When another salt is the better choice
If the product has to give a clear solution, dicalcium phosphate is the wrong salt: it is practically insoluble in water and dissolves only by reacting with acid. If the formula needs more calcium per gram and less phosphorus, tricalcium phosphate carries about 38.8% calcium with 20.0% phosphorus, and the dicalcium versus tricalcium comparison sets out the arithmetic. If the matrix is acidic and must stay clear, calcium citrate or calcium lactate is the practical starting point, and calcium carbonate is the compact high-calcium alternative when the acid reaction is acceptable.
Feed-grade dicalcium phosphate is outside this specification. It is a different product with different contaminant limits and a different documentation set, and it should not be bought against a food or supplement specification.
The dicalcium phosphate product page carries the catalog figures; the COA page shows how the calcium and phosphorus lines are reported; the identity page covers the ratio and the diffraction check; the quality page describes the release workflow.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation