01 COA & batch testing

What the dicalcium phosphate COA reports, line by line

Technical document 01 · Reviewed 2026-11-19 · Dicalcium Phosphate

On this page
  1. What the certificate has to carry
  2. The assay basis and the calcium-to-phosphorus arithmetic
  3. Limits and results, side by side
  4. What shifts from lot to lot
  5. When an outside test is worth it
  6. Comparing two suppliers

A dicalcium phosphate certificate is a list of measured values, not a description of the product. It should carry appearance, identification, assay as CaHPO₄, elemental calcium, elemental phosphorus, loss on drying, the heavy-metal panel, microbiology and sieve results, each with its method and the limit the lot had to meet. The tables below give the catalog specification; the certificate records what one lot actually reached.

In one line

The assay alone cannot describe the salt: the certificate has to report calcium and phosphorus separately, on a stated basis, and name the hydrate it dried.

What the certificate has to carry

A reader should be able to check a certificate line by line. Each entry should say what was measured, how it was measured and the limit the lot had to meet; a bare “conforms” removes the evidence. Appearance is descriptive, while identification, assay, calcium, phosphorus and loss on drying characterise the powder.

Identification is by infrared and titration, as the catalog requires. The assay is an EDTA titration of calcium expressed as CaHPO₄; phosphorus comes from a separate spectrophotometric determination, usually the molybdenum blue complex after acid digestion. The split matters: assay and calcium can be the same titration expressed two ways, while phosphorus is an independent result.

Release parameters for dicalcium phosphate
ParameterMethodRelease limit
IdentificationInfrared and complexometric titrationConforms to the reference
AssayComplexometric titration, calculated as CaHPO₄98.0–102.0%
CalciumComplexometric titration29.0–30.0%
PhosphorusSpectrophotometry after acid digestion22.0–23.5%
Loss on dryingGravimetric, oven≤2.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

The heavy-metal and microbiology lines are a safety gate, not chemistry. Report them per element and per test, with counts and absence statements.

The assay basis and the calcium-to-phosphorus arithmetic

Pure CaHPO₄ is 29.46% calcium and 22.76% phosphorus by mass. The catalog windows sit close to those figures: 29.0–30.0% calcium and 22.0–23.5% phosphorus. The assay is calculated as CaHPO₄ and its basis has to be stated. A certificate that reports the assay on the dried basis and the calcium on the as-received basis has put two different powders on one page.

The arithmetic links the three figures. If the assay comes from the calcium titration, 98.0% CaHPO₄ corresponds to 28.87% calcium, below the 29.0% calcium floor. The calcium floor corresponds to 98.44% assay. The calcium window is therefore the tighter gate at the bottom of the range, and a lot can fail it while its assay still reads inside 98.0–102.0%. The catalog contains both lines, so both are release criteria.

Phosphorus is the independent check. The phosphorus window of 22.0–23.5% corresponds to roughly 96.7–103.3% CaHPO₄, wider than the assay gate at both ends. A lot that reads 29.5% calcium and 22.4% phosphorus has a phosphorus-to-calcium mass ratio of 0.759, against 0.773 for pure CaHPO₄. The gap is small, but a ratio near 0.52 points towards tricalcium phosphate, and a ratio near zero points to a calcium salt with no phosphate at all.

Loss on drying is the third part of the basis. The catalog limit is ≤2.0%. Moisture does not change the ratio, but it changes every percentage reported on the as-received basis, and it is the figure that moves first when a pouch is left open.

Limits and results, side by side

The limit is the gate; the result is what the laboratory found. A certificate should show the two in different columns and put the method next to both. Printing the specification range in the result column gives a copy of the gate, not a result.

What the result column should contain
ParameterRelease limitResult column
Assay98.0–102.0% as CaHPO₄A measured percentage with the drying basis and the titration method
Calcium29.0–30.0%A measured percentage on the same basis as the assay
Phosphorus22.0–23.5%A measured percentage with the spectrophotometric method
Loss on drying≤2.0%A measured percentage, with the oven temperature and time
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 40 meshThe measured percentage through the sieve

“Passes specification” is a conclusion, and the numbers should let the reader reach it. Heavy metals need one figure per element; a combined total hides which element is present.

What shifts from lot to lot

The lime and phosphate sources, the precipitation pH and the drying step move the calcium and phosphorus figures. Drying also decides the hydrate: a powder dried to the anhydrous salt carries no water of crystallisation, and a dihydrate carries about 21% by mass. The catalog names the anhydrous powder, so a certificate that reports a dihydrate water figure is describing a different grade.

Phosphorus and calcium should be trended together. A drift in one figure with the other steady changes the ratio and points to a change in the reaction or in the raw material. Fluoride and lead are the lines to read on every lot, because both come from the phosphate rock and neither is removed by milling. Fluoride may be outside the catalog panel and inside the destination market's additive specification; ask for it when the destination requires it.

Particle size is a finishing specification. A change of mill or sieve moves the 40 mesh result without any change in the chemistry, and bulk density and flow are not on the catalog list at all.

When an outside test is worth it

An outside test is worth ordering for a new source, a first shipment into a regulated market, a disputed hydrate or a blend that behaves unlike its certificate. The panel is calcium by EDTA with the pH and indicator stated, phosphorus by spectrophotometry with the digestion described, loss on drying, the heavy-metal panel by ICP-MS, microbiology and particle size. Add X-ray diffraction when the hydrate or the crystal form is in question, and a fluoride determination when the destination sets a limit.

Ask the laboratory to state the sensitivity of each screen. A “not detected” entry with no limit of quantification says more about the method than about the lot. A phosphorus figure that omits the sample mass and the moisture correction cannot be checked. The report must carry the lot code, and the powder tested must be the powder retained.

Comparing two suppliers

Six lines show whether two offers describe the same powder: hydrate and CAS number; assay with its basis; calcium and phosphorus with their methods; loss on drying; heavy metals and microbiology; particle size and bulk density. An offer that matches on assay but not on hydrate or basis is an offer for a different powder.

The catalog figures sit on the dicalcium phosphate product page. The identity page sets out the calcium-to-phosphorus check, the grade page compares the anhydrous salt with the dihydrate, the calcium carbonate page is the reference for the carbonate that would show up as a phosphorus gap, the methods index describes the tests, and the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation