01 COA & batch testing

What the COA for sea buckthorn oil actually contains

Technical document 01 · Reviewed 2026-11-19 · Sea Buckthorn Oil

On this page
  1. Reading the certificate line by line
  2. The GC basis, the plant part and the percentage
  3. The limit, the result and the method
  4. What shifts from lot to lot
  5. When an outside laboratory is worth it
  6. What to put side by side

The certificate for a sea buckthorn fruit oil lot reports the full GC fatty-acid profile, with palmitoleic acid at 25.0–35.0%, oleic acid at 20.0–30.0% and linoleic acid at 30.0–40.0%, together with free fatty acid ≤1.00%, peroxide value ≤5.0 meq O₂/kg, moisture ≤0.1%, the heavy-metal panel and microbiology. The plant part — fruit or seed — decides what the profile should look like, so the certificate has to name it. The limits below are the catalog specification; the batch certificate confirms the pack in front of you.

In one line

A sea buckthorn certificate is a fatty-acid profile plus an oxidation status: the GC profile says which oil it is, and the free fatty acid and peroxide values say how it has been kept.

Reading the certificate line by line

A certificate earns its place when each line can be checked without a phone call: the test, the method, the limit and the measured result, each in its own column. A row that says only “conforms” gives a conclusion and withholds the evidence.

The profile is the identity line; the oxidation numbers are the condition line. A lot can match the palmitoleic range and still be months old, or be fresh and be the wrong oil.

Identity, oxidation and contaminants · sea buckthorn fruit oil
ParameterMethodRelease limit
AppearanceVisualOrange-red to dark red; clear to slightly hazy
IdentificationGC fatty-acid profileConforms to the reference profile
Palmitoleic acid (C16:1)GC of fatty acid methyl esters25.0–35.0%
Oleic (C18:1) and linoleic (C18:2)GC of fatty acid methyl esters20.0–30.0% and 30.0–40.0%
Free fatty acidTitration, expressed as oleic acid≤1.00%
Peroxide valueIodometric titration≤5.0 meq O₂/kg
MoistureKarl Fischer≤0.1%
Heavy metalsICP-MSEach element reported: lead ≤3, arsenic ≤2, cadmium ≤1, mercury ≤0.1 (mg/kg)
MicrobiologyTotal plate count, absence testsTotal count ≤1,000 cfu/g; yeasts and moulds ≤100 cfu/g; E. coli and Salmonella not detected

The GC basis, the plant part and the percentage

The profile comes from a gas chromatogram of the methyl esters: the oil is transesterified, the esters separate on a capillary column and the peaks are read against a standard. Laboratories normally report area percent after normalisation, which is close to mass percent but not identical; the certificate should say which basis was used.

Normalisation means the reported acids add to 100%, which is convenient and slightly dangerous: a profile that lists only the three headline acids can hide the rest. Ask for every major peak, palmitic and alpha-linolenic included. Fruit oil and seed oil differ most in palmitoleic acid and in alpha-linolenic acid, and a blend of the two lands between them.

The free fatty acid is expressed as oleic acid and measures how much oil has been split from its glycerol backbone by water and lipase. The peroxide value, in milliequivalents of active oxygen per kilogram, measures the first stable products of oxidation. Both are titrations, and both should be named as methods rather than printed as bare numbers.

The limit, the result and the method

The release limit is the boundary the lot was accepted against; the batch result is what the laboratory measured. Both belong in the table, in their own columns, with the method beside them. A result column filled with the specification range is a copy of the gate, not a result.

The result column, line by line
ParameterLimitMeasured result
Palmitoleic acid25.0–35.0%A measured percentage with the GC basis stated
Oleic and linoleic acid20.0–30.0% and 30.0–40.0%Measured percentages for each acid
Free fatty acid≤1.00%A measured percentage expressed as oleic acid
Peroxide value≤5.0 meq O₂/kgA measured figure, with the method named
Moisture≤0.1%A measured percentage
Heavy metalsPer elementA figure in mg/kg for each element, not a total

The two freshness lines deserve the closest reading. A peroxide value of 4.8 against a limit of 5.0 has passed with no headroom left for transit; a free fatty acid close to 1.00% points to damaged fruit or a wet press. A result at the edge is not a failure, but it invites a question about the next lot.

What shifts from lot to lot

Harvest year, fruit ripeness, whether the press takes pulp alone or whole berries, and the extraction temperature all move the profile. Palmitoleic acid is a trait of the pulp, so it stays steady when the raw material and the plant part are held constant and moves quickly when seed oil enters the batch. Alpha-linolenic acid is the mirror image: low in a pulp oil, higher when seed oil is present.

The oxidation numbers move with time and handling rather than with the recipe. Peroxide value climbs in a warm store and faster in a part-used container; free fatty acid climbs when water is present. Colour moves with the carotenoid content, which varies with ripeness and extraction. A shift inside the orange-red window is not an identity failure, but a trend across lots is worth reading.

When an outside laboratory is worth it

An outside laboratory earns its fee in four situations: a new source, a first shipment into a regulated market, a disputed identity, or a claim that the material is fruit oil rather than seed oil or a blend. The useful panel is the full fatty-acid profile, free fatty acid, peroxide value, moisture, heavy metals and microbiology. Add the p-anisidine value when the question is an off-note: the peroxide value falls as the first products break down, while the secondary products keep climbing.

For an identity dispute, add the unsaponifiable fraction; the sterol and tocopherol profiles differ between fruit and seed oil and between a fresh and a refined oil. A carotenoid scan is the direct check on the colour, because a dye can reproduce the appearance without reproducing the pattern. Keep the sample tested and the sample retained in one chain of custody.

What to put side by side

Put six lines side by side: the plant part named on the document; the full profile with its GC basis; free fatty acid and peroxide value with their methods; moisture; the contaminant and microbiology results; and the pack size, lot code and fill date. Two quotations that agree on palmitoleic acid but disagree on the plant part are not describing the same oil.

Three further questions separate a food-grade offer from a cosmetic one. Is the oil refined, and which steps were used? Has any tocopherol preparation been added to slow oxidation, and is it declared? Was the pack nitrogen-flushed, and how much headspace does it carry? None of these appears in a headline figure, and each one changes the shelf life and the label.

The catalog entry is on the sea buckthorn oil product page. The tests that separate fruit oil from seed oil are on the identity page, the grade choices on the grades page, the storage behaviour on the stability page, the chromatographic method in the methods section, and the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation