06 Identity & adulteration

How to prove a phosphatidylcholine lot is the named grade

Technical document 06 · Reviewed 2026-11-19 · Phosphatidylcholine

On this page
  1. The layers of identity
  2. The ratios that should agree
  3. Why X-ray diffraction does not identify PC
  4. Reading a substituted lot
  5. Writing identity into the specification
  6. Five questions for the supplier

A phosphatidylcholine lot is what its certificate says only when four checks agree: the HPLC class assay reaches the declared figure, the phospholipid profile fits a 90% fraction, the fatty acid and sterol patterns fit the plant source, and the moisture, acid value and peroxide value describe a sound lot. The PC percentage on its own cannot tell a 90% grade from a diluted lecithin or from a different source; the profile is what separates them.

In one line

Identity is the PC figure plus the profile: HPLC says how much of the class is present, and the phospholipid, fatty acid and sterol patterns say what the material is.

The layers of identity

Each layer answers a separate question, and one can pass while another fails. The document names the material and the source; the class assay measures the PC figure; the class profile shows how the rest of the phospholipid fraction is built; the source tests compare the fatty acid and sterol patterns with a reference; the condition tests describe hydrolysis and oxidation.

Layers of phosphatidylcholine identity
LayerQuestionTestWhat it proves
DocumentAre the material and source named?Name, CAS 97281-44-2, sourcePaperwork only
Class assayHow much PC is present?HPLC against a PC standardThe grade, not the source
Class profileIs the fraction built as expected?PE, PI, PA and lyso-PC by HPLCThe fractionation and any blend
SourceWhich plant is it from?Fatty acid and sterol profiles by GCThe source claim
ConditionIs the lot sound?Moisture, acid value, peroxide valueHydrolysis and oxidation state

A supplier can name the material correctly and still ship a blend, a dilution or a different plant source. The later layers are the ones that catch it, and a certificate that stops at the first two has not tested them.

The ratios that should agree

The figures on a PC certificate have to fit one another. The PC result should normally sit at or below the total phospholipid figure, because PC is one class inside that total. The residual PE, PI and PA should be small in a 90% grade; a high PE or PI result points to incomplete fractionation or to added lecithin. Phosphorus should reproduce the total phospholipid figure when the stated factor is applied, and the choline result should fit the PC figure.

Ratios to check on a phosphatidylcholine certificate
RatioWhat it testsA shift suggests
PC against total phospholipidsPC sits inside the totalA different method, a blend or a calculation error
PC against PE, PI and PAThe residual pattern of a 90% gradeIncomplete fractionation or added lecithin
Phosphorus against total phospholipidsThe stated factor reproduces the totalDilution or an inconsistent factor
Choline against PCAbout 13% choline in soy PC by massA different source, a blend or a non-PC choline salt
Alpha-linolenic acid in the fatty acid profileSoy retains a measurable alpha-linolenic fractionA sunflower or egg source
Sterol profileThe sterol pattern of soy against sunflowerA source claim that does not match

For a 90% PC powder, the choline arithmetic lands near 12% by mass. That is a consistency check, not a label claim: the exact value depends on the lot and its fatty acid composition, and a choline claim has its own conditions in the destination market.

Why X-ray diffraction does not identify PC

The catalog material is a wax, not a crystal. Phosphatidylcholine is amorphous or semi-solid at room temperature, so an X-ray scan shows a broad hump with no sharp reflections, and no reference pattern identifies “soy PC”. A certificate that reports diffraction conformity without naming a phase has reported nothing the reader can check.

The technique still has a use: sharp peaks in a powder reveal a crystalline carrier or filler, and their positions can identify it. That is a check on the carrier, not proof of the phospholipid.

FTIR shows the phosphate and ester bands and supports the phospholipid assignment, but it does not separate soy from sunflower. The class, fatty acid and sterol methods do. The methods library sets out the reach and the blind spot of each technique.

Reading a substituted lot

Common phosphatidylcholine substitutions and the signals
AdulterantWhat it doesSignalTest
Lecithin or deoiled lecithinLowers the PC figure and lifts the other classesPC low; PE, PI and PA high; AI out of line with the PC figureHPLC class profile, AI
Soybean oilAdds neutral oil and dilutes the PCPC low; oil pattern in the fatty acidsHPLC, fatty acid GC
Sunflower lecithin or PCChanges the source and the allergen statementLittle or no alpha-linolenic acid; sterol mismatchFatty acid and sterol GC
Synthetic or single-species PCRaises the PC peak with a narrow fatty acid patternPC high; no alpha-linolenic fraction; one dominant fatty acidFatty acid GC, profile
WaterRaises moisture and lowers the as-is PC figureMoisture high; PC low as-isMoisture, PC
Residual solventCarries solvent residue from the extractionHeadspace result; odourResidual-solvent GC

Colour is the least reliable evidence. White to light yellow covers a broad range, and a blend can be made to match it. The class profile, the fatty acid pattern and the mass balance are harder to imitate.

Writing identity into the specification

  • “Phosphatidylcholine, soy-derived, CAS 97281-44-2, source named.”
  • “PC ≥90.0% by HPLC; method, detector, standard and basis stated.”
  • “Phospholipid class profile (PC, PE, PI, PA and lyso-PC) reported for the lot.”
  • “Fatty acid profile by GC, with the alpha-linolenic fraction reported; sterol profile available.”
  • “Moisture ≤1.0%; acid value ≤30 mg KOH/g; peroxide value ≤5.0 meq O2/kg.”
  • “Heavy metals, microbiology and residual-solvent statement as agreed for the lot.”
  • “Soy allergen and GMO statements attached; form and particle size for a powder.”

Five questions for the supplier

  1. Which plant source is this lot, and which lecithin lot was it fractionated from?
  2. Can you provide the PC chromatogram and the full phospholipid class profile, not only the percentage?
  3. What do the fatty acid and sterol profiles show, and do they fit the declared source?
  4. What are the moisture, acid value, peroxide value and residual-solvent results for this lot?
  5. If the grade or the source is disputed, will you test the retained sample jointly with us?

Those five answers form an identity file; one PC percentage does not. The product hub carries the catalog specification; the lecithin page covers the mixture. The COA page shows where each figure sits on the certificate, the grades page compares the potency and form, the methods library describes the separation and the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation