02 Grade comparison

Choosing a phosphatidylcholine grade: potency, form and source

Technical document 02 · Reviewed 2026-11-19 · Phosphatidylcholine

On this page
  1. Why the range exists
  2. The grades side by side
  3. Waxy solid, powder and the line
  4. Dose arithmetic for each grade
  5. What to write into the grade specification
  6. When another grade is the wrong purchase

Phosphatidylcholine is sold as a family of grades that differ in the PC figure, the physical form, the plant source and the degree of modification. The catalog grade is ≥90.0% PC by HPLC, supplied as a waxy solid or a powder, and it is the fraction that a lecithin label does not describe. The grade decides the mass per declared dose, the flow on the line and the allergen statement.

In one line

A PC grade is fixed by four choices: the PC figure, the physical form, the plant source and whether the molecule has been modified.

Why the range exists

Lecithin is a mixture; a PC grade is a fraction of it. The range exists because the fraction can be concentrated to different figures, dried into different physical forms, taken from different plants and modified after fractionation. Each choice is a separate specification line, not a marketing variant.

The PC figure is the first fork. A 70% grade and a 90% grade are both PC concentrates, but the mass needed for a declared dose differs by nearly 30%. The catalog sits at 90%, which leaves less room for other phospholipids and oil.

Source is the second fork. The catalog material is soy-derived, CAS 97281-44-2. A sunflower-derived PC is a different source with a different fatty acid pattern and a different allergen statement; an egg-derived PC is a third. They are not interchangeable under one label, even when the PC figure on the certificate is the same.

The grades side by side

Phosphatidylcholine grades and related products
GradePC figureWhat else is presentFormTypical use
PC 70About 70% by HPLCMore PE, PI and residual oil than the 90% gradeWaxy solid or powderWhere a lower PC density is acceptable
PC 90 (catalog)≥90.0% by HPLCResidual classes and a small oil fractionWaxy solid or powderDeclared PC dose in capsules and blends
Soy lecithin (reference)PC is part of the mixturePE, PI, PA, oil and sterolsFluid or powderEmulsifier, mixed phospholipid source
Hydrogenated PCDepends on the starting gradeSaturated fatty acids; different oxidation behaviourWaxy solidWhere a saturated phospholipid is specified
Lyso-PCDepends on the starting gradeOne fatty acid removed; more hydrophilicPowder or dispersionWhere water dispersibility is the point
Carrier-supported PCThe figure is read on the blendA declared carrierPowderDry blends and stick packs

The table separates two things that are often conflated: the PC figure and the total phospholipid figure. A 70% PC grade can carry a total phospholipid figure above 90%, while a 60% lecithin carries PC as only part of its phosphatide fraction. The two figures answer different questions.

Hydrogenated and lyso-PC are different products, not higher grades of the same material. Hydrogenation changes the fatty acid saturation and the oxidation behaviour; enzymatic hydrolysis removes one fatty acid and changes the water dispersibility. Both need their own specification and their own label name.

Waxy solid, powder and the line

The catalog form is a waxy solid or a powder. The waxy solid softens with warmth and can be weighed as a lump or a flake; the powder flows and is easier to blend but takes moisture faster. Neither is a free-flowing crystalline solid, and a hopper designed for a mineral powder may bridge on PC.

PC is hygroscopic. An open pouch on a bench picks up water, the surface becomes tacky, and the moisture figure rises. The material is also heat-sensitive: a warm room softens the solid, and a hot hold accelerates hydrolysis and darkening.

For a powder, put bulk density, particle size and flow on the specification. For a waxy solid, put the softening behaviour and the pack format on it. A particle-size limit written for a powder cannot be applied to a waxy solid without saying how the sample was prepared, and a flow figure measured on one form says nothing about the other.

Dose arithmetic for each grade

Start with the declared ingredient. A PC claim uses the PC figure as the divisor. A lecithin claim uses the weight of the mixture; a phospholipid claim uses the total phosphatide figure. Three claims, three divisors.

For a label that declares 250 mg PC, a 90% grade needs 250 ÷ 0.90 = 278 mg of powder, while a 70% grade needs 357 mg, and a lecithin carrying 20% PC needs 1,250 mg. The figures are arithmetic, not a dose recommendation. They show why a switch of grade changes the capsule size.

If the label declares choline rather than PC, the divisor changes again. Soy PC carries about 13% choline by mass, so 250 mg PC delivers roughly 32.5 mg choline; the exact figure belongs to the lot and its fatty acid composition. A choline claim has its own conditions in the destination market and should not be inferred from the PC weight.

What to write into the grade specification

  • “Phosphatidylcholine, soy-derived, CAS 97281-44-2, source named.”
  • “PC ≥90.0% by HPLC; method, detector, standard and basis stated.”
  • “Phospholipid class profile reported: PE, PI, PA and lyso-PC, with the total phospholipid figure.”
  • “Moisture ≤1.0%; acid value ≤30 mg KOH/g; peroxide value ≤5.0 meq O2/kg.”
  • “Heavy metals and microbiology as listed; residual-solvent statement for the extraction route.”
  • “Form: powder or waxy solid; particle size and bulk density for a powder.”
  • “Soy allergen and GMO statements attached; destination market confirmed.”

Name the basis of the PC figure, not only the number. A certificate that says 90% without saying whether it is as-is or dried, and without naming the detector, has left the grade open to interpretation. The same rule applies to the moisture line: Karl Fischer and loss on drying are different measurements.

When another grade is the wrong purchase

If the claim is on lecithin, a 90% PC grade is the wrong material even though it contains PC: the label names a mixture, and the certificate does not carry the lecithin figures. If the claim is on total phospholipids, a PC figure alone does not answer it. If the formula needs an emulsifier rather than a declared PC dose, the whole lecithin is the simpler purchase.

A soy-free claim needs a different plant source, not a lower PC figure. A hydrogenated or lyso-PC claim needs the modified grade and its own specification. A change in grade is a change control: it moves the mass, the label, the allergen statement and possibly the market file.

The product hub carries the catalog specification; the lecithin page covers the mixture; the level-four comparison takes the comparison further. The COA page shows how the grade is reported, the identity page covers the source checks, the methods library explains the assays and the quality page sets out release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation