02 Grade comparison

60% is not a grade: choosing an omega-3 concentrate

Technical document 02 · Reviewed 2026-11-20 · Omega-3 Concentrate

On this page
  1. Why 60% is not a grade
  2. The grades side by side
  3. What the oil is like to handle
  4. The dose arithmetic and the ratio
  5. Writing the grade into the specification

An omega-3 concentrate is specified by three decisions: the EPA plus DHA total, the EPA to DHA ratio inside that total, and the lipid form. This catalog is a 60% concentrate, EPA 30.0–36.0% and DHA 20.0–26.0% by GC with a total of at least 60.0%, supplied as an ethyl ester or a triglyceride. Two oils that both read 60% can deliver different amounts of each acid and carry different label names.

In one line

A concentrate is defined by three decisions before the word grade means anything: the EPA plus DHA total, the EPA to DHA ratio inside it, and whether the oil is an ethyl ester or a triglyceride.

Why 60% is not a grade

The word concentrate describes a process, not a fixed product. A refiner transesterifies the oil to ethyl esters and distils the esters, or complexes the acids with urea and separates them; a re-esterification step can put the fatty acids back onto a glycerol backbone. Each route can reach 60%, and each leaves a different oil with a different certificate.

The total is only the first number. The ratio decides how much EPA and how much DHA a serving carries. The form decides the ingredient name, the free-fatty-acid behaviour and the absorption route. Grade is the combination, and a quotation that names only the percentage has named one of three.

Concentration is not a quality ladder. A 60% oil is not better than a refined 18/12 oil; it is a different ingredient for a different capsule size and a different label. The question is what the dosage form can carry and what the destination file permits, not which number is higher.

The grades side by side

Concentrate grades, their typical totals and what changes
GradeTypical EPA+DHALipid formWhat it changes
Refined fish oil 18/12About 30%TriglycerideA different product; the baseline oil
60% concentrate, ethyl ester (this product)≥60%Ethyl esterSmaller capsule; ester ingredient name and mass basis
60% concentrate, triglyceride≥60%Re-esterified triglycerideGlycerol backbone restored; an extra process step
High-EPA concentrateAbout 70–90%, EPA-dominantEither formA different ratio and a different label dose
High-DHA concentrateAbout 70–90%, DHA-dominantEither formA different ratio; often a separate source question
Concentrate powder on carrierDeclared oil loadOil on a carrierFlow, a carrier declaration and a different mass

The table separates catalog lines from typical market grades. This page supplies the second row: at least 60.0% EPA+DHA, ethyl ester or triglyceride, with EPA and DHA inside the catalog windows. The first row is the refined oil, specified on the fish oil product page; the last row is a powder on a carrier, quoted on request and carrying its own specification.

The total and the two individual ranges are read together. With DHA capped at 26.0% and the total floored at 60.0%, a conforming lot cannot sit at 30.0% EPA; the effective working window is narrower than the printed windows, and the ratio moves with it. That is why the ratio belongs in the specification beside the total.

What the oil is like to handle

The concentrate is a clear, pale yellow oil at room temperature, insoluble in water and soluble in fats and organic solvents. It is less viscous than the refined oil it came from, because distillation has removed the heavier glycerides and part of the minor lipid fraction. Density is below 1, so a 1 kg amber bottle holds a little over a litre.

Contact materials should be stainless steel or glass. Copper and iron catalyse oxidation at low levels, and a brass fitting or a mild-steel liner is a contact the specification should exclude. Keep the headspace small, close the bottle after sampling and record the opening date on the drum.

Cold storage can cloud a triglyceride concentrate as higher-melting fractions separate; the cloud is not a defect by itself, and warming returns a clear oil. An ethyl ester concentrate generally stays clear at lower temperatures. Neither observation replaces PV, p-AV and FFA on the certificate.

Odour is the practical freshness check. A mild marine smell is expected; a sharp or paint-like one points to aldehydes. Colour is weaker evidence, because deodorisation and bleaching can leave a pale oil that is already oxidised.

The dose arithmetic and the ratio

At 60% EPA+DHA, one gram of oil carries about 600 mg of the two acids. At a nominal 35/25 split, that is about 350 mg EPA and 250 mg DHA. A 1,000 mg softgel built on the concentrate therefore carries about 600 mg EPA+DHA, against about 300 mg for the same fill of 18/12 oil.

Work backwards from the label. A serving that declares 500 mg EPA+DHA needs about 0.83 g of a 60% concentrate or about 1.67 g of 18/12 oil. If the label declares one acid, the ratio governs: 300 mg EPA from a 35% EPA oil needs about 0.86 g of oil, and the DHA arrives at whatever the ratio supplies. Those are arithmetic examples, not recommendations.

The form changes the mass basis too. A certificate reported on a free-fatty-acid-equivalent basis reads about 8% lower than the same lot reported as ethyl esters, so the capsule fill and the label figure have to sit on one basis. A label built on one basis and a certificate on the other can disagree by more than the analytical tolerance.

Writing the grade into the specification

Six lines fix the grade:

  • Source and species, with the fish oil and the process route named.
  • Form: ethyl ester or triglyceride, stated on the certificate and on the label.
  • EPA and DHA ranges, the total floor, and the GC basis, including whether the result is area per cent or mg/g and on which equivalent basis.
  • Free fatty acid ≤0.10%; PV ≤5.0 meq O₂/kg; p-AV ≤20.0; a TOTOX ceiling if one is agreed.
  • Heavy metals and microbiology as listed; dioxins and PCBs where the market requires them.
  • Antioxidant type and level, the pack, and the fish allergen statement.

A specification that says only “omega-3 60%” leaves the ratio, the form and the basis open, and three suppliers can answer it with three different oils. Write the three decisions, then the limits.

The product hub carries the catalog lines; the COA page shows how the figures are reported; the stability page covers oxidation; the methods index covers the GC and the contaminant tests; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation