01 COA & batch testing

What the COA for omega-3 concentrate actually contains

Technical document 01 · Reviewed 2026-11-20 · Omega-3 Concentrate

On this page
  1. The certificate as a lot report
  2. The GC basis and the mass basis
  3. Release limits, results and the oxidation pair
  4. What moves between lots
  5. When to send a sample out
  6. What to compare between suppliers

The certificate for an omega-3 concentrate lot reports the GC fatty-acid profile, EPA and DHA separately and as a total, the lipid form, free fatty acid, peroxide and p-anisidine values, and the contaminant panel. The limits here are the catalog gates; the batch COA carries the measured result. Total, form and oxidation decide a release, and none is readable alone.

In one line

The certificate has to be read on three axes at once: the EPA and DHA figures against their total, the ester or triglyceride form the figures were measured in, and the oxidation pair that says whether the oil is still fresh.

The certificate as a lot report

A certificate is auditable when each line carries a method, a limit and a measured result. The header should give the lot code, fish source, production date and declared form, because the form changes what several lines mean.

The form is a certificate line, not a footnote. An ethyl ester lot and a triglyceride lot can read 60% EPA+DHA and still be different ingredients with different label names and mass bases.

Composition and form · omega-3 concentrate
ParameterMethodRelease limit
AppearanceVisualClear, pale yellow oil
IdentificationGC-FAME, full profile against a referenceProfile conforms
EPA (C20:5 n-3)GC-FAME30.0–36.0%
DHA (C22:6 n-3)GC-FAME20.0–26.0%
EPA + DHAGC-FAME, sum of the two acids≥60.0%
Lipid formIntact-lipid analysis; glycerol or ethanolEthyl ester or triglyceride, as declared
Free fatty acid, as oleicAcid–base titration≤0.10%

The EPA and DHA lines are separate on purpose. A 60% total can be split at different ratios, and the splits deliver different amounts of each acid. The form line decides whether the milligram figures describe an ester or a glycerol ester.

The GC basis and the mass basis

The method converts the oil to methyl esters, runs them down a capillary column and detects them by flame ionisation. The result can be reported as area per cent, as milligrams per gram of oil, or as free fatty acid equivalents. Those are different numbers for the same lot.

Area per cent and milligrams per gram are not the same measurement. The glycerol backbone, the ethanol moiety and the unsaponifiable fraction sit outside the fatty-acid peak area, so the certificate must state its basis and the label dose must be derived from it. A label that declares 600 mg EPA+DHA from a 60% oil is using a mass basis; 60% by area has not proved that mass.

The ester form adds a second conversion. On a free-fatty-acid-equivalent basis the ethanol moiety of an ethyl ester is excluded, so the same lot reads roughly 8% lower than on an ethyl-ester basis. Trade monographs such as the GOED voluntary monograph use the acid-equivalent basis, while a supplier certificate may report ethyl esters. Ask which basis is on the page before comparing two offers.

Read the total with the two individual ranges. The catalog allows EPA 30.0–36.0% and DHA 20.0–26.0%, with a total floor of 60.0%. A lot at the bottom of both windows would sum to 50% and fail, so the total is the binding gate: with DHA at its 26.0% ceiling, EPA cannot fall below 34.0% and still be released.

Release limits, results and the oxidation pair

The release limit is the boundary for the lot; the result is what the laboratory measured. When the result column repeats the acceptance range, it is a copy of the gate rather than a measurement.

Oxidation and contaminants · omega-3 concentrate
ParameterMethodRelease limit
Peroxide valueIodometric titration≤5.0 meq O₂/kg
p-Anisidine valueSpectrophotometric≤20.0
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

Oxidation is read as a pair. PV counts hydroperoxides, the first products of the reaction; p-AV counts the aldehydes that appear as they break down. Hydroperoxides decompose as the oil ages, so PV can fall while p-AV rises, and a low PV on an old lot is not evidence of freshness. TOTOX is twice PV plus p-AV: a lot at both catalog ceilings would calculate to 30, while the GOED monograph uses 26. That 26 is a trade benchmark, not a statutory limit; a buyer who wants it must write it into the purchase specification.

Free fatty acid is a separate line and a tight one at ≤0.10%. The concentrate is distilled, so hydrolysis is limited, but a wet or warm pack can still move the figure. FFA is a hydrolysis measure, not an oxidation one; a low figure does not prove freshness.

What moves between lots

The distillation cut is the largest lever: the cut point decides how much EPA and DHA are collected, whether the route is transesterification and distillation or urea complexation. A small change in the cut moves the total and the ratio together; the species and the season move the starting oil.

Molecular distillation runs hot, and heat can isomerise part of the all-cis EPA and DHA to trans isomers. The catalog does not set a trans-isomer limit, so a buyer who cares should ask for the figure and agree a ceiling. If an antioxidant is used, its type and level belong on the certificate or the TDS, because a change is a material change even when the assay holds.

Colour and odour are the least quantitative lines and still useful: a pale, mild oil can be oxidised, a darker, fishier one can be fresh but poorly deodorised. Read them beside PV and p-AV.

When to send a sample out

Order an independent test for a new source, a market launch, an unproven form claim or a disputed oxidation result. The panel should answer the questions the certificate leaves open: GC-FAME with the chromatogram, and EPA, DHA, DPA and the trans isomers reported separately; intact-lipid analysis for the form; sterols and cholesterol where a vegetable oil is suspected; PV, p-AV and TOTOX by named methods; ICP-MS for the metals; and GC-HRMS for dioxins and PCBs where the market requires them.

Each screen needs its limit of quantification: “not detected” without one describes the method, not the sample. Record the chain of custody and lot code, and test the retained sample.

What to compare between suppliers

Six lines make a comparison: the fish source and species; the form; EPA, DHA and the total with the basis; FFA, PV, p-AV and TOTOX; the contaminant panel; and the pack size with the lot code. Two offers that agree on 60% but differ on form, ratio or basis describe different oils.

Traceability covers who distilled the lot, which cut, whether an antioxidant was added and whether the drum was nitrogen-blanked. The catalog specification sits on the omega-3 concentrate product page. The refined oil is specified on the fish oil product page; the form and ratio are compared on the grades page; the oxidation story is on the stability page; the GC method and the other tests are indexed under methods; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation