06 Identity & adulteration

How we prove a DHA lot is DHA

Technical document 06 · Reviewed 2026-11-19 · DHA Powder

On this page
  1. Four layers of identity
  2. The DHA and EPA profile
  3. Why an X-ray scan is not the identity test here
  4. The adulteration routes to test for
  5. How to write identity into the specification
  6. Five questions for a DHA supplier

Identity rests on four layers: the documents, the GC fatty-acid profile, the oil-to-carrier mass balance and the oxidation record. A DHA number alone can be produced by a blend; the chromatogram and the declared source are what make the number an identity. The catalog specification fixes DHA at ≥10.0% by GC, but the proof is the set of records that agree with it.

In one line

A DHA number is a result; identity is the chromatogram, the oil load and the declared source agreeing with it.

Four layers of identity

Layer one is the paper: product name, source, CAS 6217-54-5, grade, specification revision and lot code. It is necessary and the easiest layer to copy. Layer two is the chromatogram: the fatty-acid methyl esters separated by GC, with DHA identified against a standard and the peak area integrated. Layer three is the mass balance: how much oil the powder actually contains, and how much is starch, moisture and antioxidant. Layer four is the condition of the oil: peroxide value, p-anisidine value, colour and odour.

A lot can pass layer one and fail layer three. A powder at 10% DHA built on a low oil load carries more starch per gram of DHA than one built on a higher load; both meet the assay, but they are not the same material. A lot can also pass layers one and three and fail layer four, because a fresh-looking assay says nothing about the hydroperoxides already in the oil.

The four identity layers and the failure each one catches
LayerEvidenceWhat it catches
DocumentName, source, CAS, grade, lot code, specification revisionA generic certificate with no lot link
ChromatogramGC fatty-acid profile, DHA and EPA peaks, standard and integrationA blend or a different oil under the same assay
Mass balanceOil load or fat content, carrier, moisture, antioxidantA diluted powder passing on a high-oil basis
ConditionPeroxide value, p-anisidine value, colour, odourAn oxidised oil behind a passing assay

The DHA and EPA profile

DHA is identified by retention time against a certified standard, not by the size of a peak. The certificate should say which standard, which column and which detector, and it should attach the chromatogram. A peak that co-elutes with DHA in one temperature programme can separate in another; the method belongs in the record.

The profile around DHA is the second check. A fish oil usually carries a measurable EPA fraction and a sterol pattern that includes cholesterol; an algal oil can be high in DHA with little EPA and a different sterol pattern. Neither is a law, because blends and fractions exist, but the profile has to agree with the declared source. If the label says algal and the chromatogram looks like a fish oil, the source statement is the document to challenge first.

The expression basis matters as much as the peak. DHA can be reported as free fatty acid, as triglyceride or as methyl ester, and area percent is not weight percent of the powder. A certificate that reports a DHA percentage without the basis has given a number that cannot be converted into a dose or compared with another supplier's number. The certificate should state the basis and the conversion.

Why an X-ray scan is not the identity test here

X-ray diffraction reads crystal lattices. The DHA in this powder is an oil, and the carrier is a modified starch that is largely amorphous, so there is no DHA lattice to diffract. An XRD pattern can show a crystalline phase — starch, a mineral or an inorganic adulterant — but it cannot confirm or quantify DHA. A clean pattern is not proof of identity, and crystalline peaks are not proof of adulteration.

A rapid spectroscopic screen has the same limit. FTIR can show oil, starch and moisture, and it is useful for incoming comparison against a reference spectrum, but it does not replace the GC assay. Identity for this material is a separation method, because the analyte is one fatty acid among several in a mixture.

The adulteration routes to test for

The first route is oil substitution: fish oil sold as algal, or a different oil blended into a concentrate. The fatty-acid profile and the sterol pattern are the tools; a single DHA figure is not. The second is dilution: less oil in more carrier, with 10% DHA held by using a more concentrated oil. The mass balance catches it, which is why oil load belongs on the specification.

The third is oxidation masking: an aged oil blended with fresh oil or dosed with antioxidant to bring the peroxide value under the limit. Peroxide value can look acceptable while p-anisidine value and colour show the history. The fourth is a form change: an ethyl-ester oil declared as a triglyceride, or the reverse. The label should name the form, and the analytical record should say whether the oil was transesterified before injection, because methylation erases the difference.

The fifth is a carrier change. A different starch can alter the allergen statement, the flow and the fill weight without changing the DHA figure. The declared carrier and the source statement are part of identity, not packaging detail. The COA page lists the tests that make these routes visible.

How to write identity into the specification

Write the material as “Microencapsulated DHA powder, 10% DHA (GC), [source] oil, carrier modified starch, antioxidant [name], ≥95% through 40 mesh.” Add the DHA limit and method, the expression basis, EPA reported, the oil load or fat content, moisture, peroxide value, p-anisidine value, the heavy-metal and microbiology panels, and the allergen statement.

Then add the records: lot code on the certificate, pack and retained sample; the chromatogram; the source statement; the carrier and antioxidant declaration; and the specification revision. A specification without the source and the oil load describes a grade, not a material. The grade page explains what changes when the form or the load changes, and the compliance page explains why the source has to be on the file.

Five questions for a DHA supplier

Five questions that turn a DHA quotation into an identity record
QuestionWhy it matters
What is the oil source, and is it algal or fish?Sets the allergen, the regulatory route and the expected profile
What is the DHA result, the GC method and the expression basis?Turns a percentage into a comparable, convertible figure
What are the EPA and the full fatty-acid profile?Shows whether the oil matches the declared source
What are the oil load, carrier and antioxidant?Exposes dilution and fixes the label and the fill weight
What are the peroxide and p-anisidine values, with the chromatogram and a retained sample?Separates a fresh lot from an aged one and lets a third party repeat the work

Ask the same five questions and compare the answers. The supplier that answers with a certificate, a chromatogram and a lot code is giving an identity record; the one that answers with a specification range is giving a grade. The DHA powder hub carries the catalog specification, and the COA glossary entry defines the document terms.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation