06 Identity & adulteration

How we prove a CLA lot is the declared isomer

Technical document 06 · Reviewed 2026-11-19 · CLA Powder

On this page
  1. Four layers that have to agree
  2. The isomer ratio is part of the identity
  3. Why XRD does not identify CLA
  4. What substitution looks like
  5. How to write the identity into the specification
  6. Five questions to a supplier

A CLA lot is identified at four levels: the document set, the total CLA by GC, the isomer distribution and the oil load inside the starch. A CAS number and a 10% result do not separate a safflower-derived CLA oil from a diluted or partly oxidised one. Identity is the set of figures that agree with each other and with the specification.

In one line

A CLA lot is identified by its total CLA, its isomer ratio and its oil load together, not by a CAS number or a single assay.

Four layers that have to agree

The first layer is the paperwork: a specification naming the grade, oil source, isomer ratio and oil load; a lot certificate; and one lot code across certificate, pack and retained sample. A file that does not close is a reason to stop before the laboratory work.

The second layer is the total CLA by GC. The third is the distribution of the main isomers. The fourth is the matrix: how much oil the starch carries, which starch and antioxidant, and how much oil sits on the surface. CLA content equals oil load multiplied by the CLA concentration of the oil, so a total CLA figure that cannot be reconciled with the declared oil load is an identity problem even when each number looks plausible on its own.

The four identity layers for a microencapsulated CLA powder
LayerWhat it showsWhat it misses
Document setGrade, source, lot trace and the specification released againstWhether the powder in the pack is that lot
Total CLA by GCThe mass of conjugated linoleic acid in the powderWhich isomers make up the total
Isomer distributionThe c9,t11 and t10,c12 split, and the minor isomersThe oil load and the carrier
Matrix and oil loadHow much oil the starch carries and what else is presentWhether the oil is fresh or oxidised

The isomer ratio is part of the identity

Conjugated linoleic acid is not one molecule. It is a family of C18:2 isomers with conjugated double bonds, and the two that dominate commercial oils are c9,t11 and t10,c12. They have the same formula and different geometry: c9,t11 is (9Z,11E), also called rumenic acid, and t10,c12 is (10E,12Z). A certificate that reports only the total makes them look interchangeable, which they are not on a specification or a label.

The ratio is set by the oil process, not by the starch. Isomerisation of linoleic acid produces a mixture, and the purification decides the final split. Commercial CLA oils are often close to 1:1, but that is a process outcome, not a default that can be assumed. The specification should state each main isomer as a percentage of the powder, of the oil or of total CLA, and it should say which basis is used; a ratio without a basis is not testable.

The GC method has to resolve the two peaks. They elute close together, and a short column or a loose temperature programme can merge them or merge one with linoleic acid. The certificate should name the column, the detector, the standard for each isomer and the integration. If the laboratory reports only a total, ask for the chromatogram and the peak areas.

The CAS number is a useful label but not an identity test. This catalog lists CAS 2420-56-6 for CLA; registries also assign separate numbers to individual isomers, so the CAS does not give the ratio. Use it to find the material, then use GC and oil load to prove the lot.

Why XRD does not identify CLA

X-ray diffraction sees crystalline structure. A CLA oil is liquid and amorphous at room temperature, so it produces no CLA diffraction pattern. The starch carrier may be crystalline or partly amorphous, and its pattern changes with source, modification and drying; XRD is a tool for the carrier, not for the oil. A diffractogram that matches a starch reference tells you the matrix is starch. It says nothing about whether the oil inside is CLA, a different oil or a mixture.

The identity method for the oil is GC, supported by fatty acid and sterol profiles when adulteration is suspected. XRD belongs in carrier characterisation, not in the CLA identity block. Asking for an XRD pattern as proof of CLA is asking the wrong test. The XRD method note covers the technique.

What substitution looks like

Common CLA powder substitutions and the test that catches each
SubstitutionWhat it looks likeTest that catches it
Dilution with a non-CLA oilCLA figure met, oil load high, fatty acid profile shiftedGC total CLA against oil load; fatty acid profile
Low-CLA oilMore oil needed to reach 10%, so the oil load is highOil load arithmetic; sterol and tocopherol profile
Oxidised oilAssay passes, peroxide or p-anisidine value highPV and p-AV on a stated basis; colour and odour
Carrier overloadCLA figure met with a low oil load; dense, starchy powderOil load, starch content, microscopy
Wrong isomer ratioTotal CLA correct, c9,t11 and t10,c12 split shiftedGC isomer distribution with standards

A 10% CLA powder with a 12% oil load implies an oil that is about 83% CLA; a 10% CLA powder with a 20% oil load implies an oil that is about 50% CLA. If the certificate gives the CLA figure and not the oil load, the buyer cannot run the check.

How to write the identity into the specification

Write the product as a full identity, not a category: “Microencapsulated conjugated linoleic acid powder, 10% total CLA by GC, c9,t11 and t10,c12 reported as a percentage of total CLA with the ratio and its tolerance, oil load declared, carrier modified starch with a named antioxidant, ≥95% through 40 mesh, CAS 2420-56-6, source oil named.” Add the oxidation limits, the moisture limit, the heavy metals and the microbiology, and name the methods.

The ratio needs a tolerance. A specification that says “1:1” with no range cannot be tested; the tolerance decides what counts as the same oil. State whether each isomer is a percentage of the powder or of the total CLA, and keep the same basis on the certificate and the label. The isomer page covers the label side of that choice, and the COA page lists the certificate lines.

Five questions to a supplier

  1. What is the total CLA and the full isomer distribution on the lot, with the chromatogram and the standards named?
  2. What is the oil load, and how was the oil extracted from the starch before GC?
  3. Which oil is the CLA made from, and what do the fatty acid and sterol profiles show?
  4. What are the peroxide and p-anisidine values, on what basis, and what is the surface oil?
  5. Which starch and antioxidant are used, from which source, and what is the allergen statement for the lot?

If the supplier cannot give the oil load, the isomer split or the oxidation basis, the 10% figure is not an identity. The catalog specification is on the CLA powder hub, and the certificate terms are in the assay glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation