CLA isomers: c9,t11 vs t10,c12 and the label
Conjugated linoleic acid is a family of isomers, and the two that dominate commercial oils are c9,t11 and t10,c12. They share a molecular formula but are different molecules on a specification and, where a brand names one, on a label. The ratio, the basis and the method belong in the specification before the label is written.
The c9,t11 and t10,c12 isomers are different label ingredients, so the ratio belongs in the specification before it reaches the label.
Two isomers, one name
Linoleic acid is an 18-carbon fatty acid with two double bonds separated by a methylene group. Conjugated linoleic acid has the same formula, C18H32O2, but the double bonds are adjacent, separated by one single bond, and that changes the geometry and the chemistry. The c9,t11 isomer has its double bonds at carbons 9 and 11, with cis geometry at 9 and trans at 11; it is (9Z,11E) and is also called rumenic acid. The t10,c12 isomer is (10E,12Z). Both are found in ruminant fats, and both are produced when linoleic acid is isomerised industrially to make a CLA oil.
They are not interchangeable. A specification that gives only “CLA 10%” does not say which isomer is present or in what proportion, and a label that names one isomer is making a claim the certificate has to support. The distinction is chemical, not a marketing preference: the two have different melting behaviour and different analytical retention times.
Ratio, total and basis
Commercial CLA oils are often close to a 1:1 mix of c9,t11 and t10,c12, because the isomerisation and purification are tuned to that balance. Close to 1:1 is a process outcome, not a legal definition. Some oils are enriched in one isomer, and the ratio can drift with the raw material and the process. The specification should therefore give each main isomer, not only the total, and it should give a tolerance around the ratio.
The basis has to be stated. An isomer figure can be a percentage of the powder, a percentage of the oil or a percentage of total CLA. The three are different numbers. A certificate that says “c9,t11 40%” without a basis could mean 40% of the oil, 40% of the CLA or 40% of the powder, and the reader cannot tell. Write the basis into the specification and repeat it on the certificate and the label.
The total is the sum of the isomers, but only if the method integrates them all. A laboratory can report a total from the two main peaks and ignore the minor isomers, or sum every conjugated peak; the two totals are not the same. Ask which convention the certificate uses, and ask for the chromatogram. The identity page explains why the ratio and the oil load have to agree with the total.
What the label can say
The ingredient name is “conjugated linoleic acid”, with “CLA” as the familiar abbreviation. If the brand wants to name an isomer, the label should use the isomer name the specification supports: c9,t11, t10,c12, or a declared mix. A label that says only “CLA” does not promise a ratio; a label that says “c9,t11” promises that isomer, and the certificate has to show it lot by lot.
The oil load drives the fat declaration. CLA is a fatty acid, so the powder contributes fat in proportion to the oil it carries, not in proportion to the CLA figure alone. The carrier and the antioxidant are ingredients and belong in the ingredient list; a starch carrier and an antioxidant are not invisible on the label. If the carrier is wheat-derived or the antioxidant is soy-derived, the allergen statement has to follow the source.
Do not put a ratio in the brand name unless the specification, the certificate and the label all use the same basis and the same tolerance. A “1:1” claim that the certificate reports as 45:55 is a mismatch the buyer will find at the first audit. The grade page covers how the oil load changes with the grade.
What the rules say about the name
In the EU and the UK, the ingredient has to be named in the ingredient list in a way the consumer can understand, and any health claim has to be authorised under Regulation 1924/2006. As of this review, the EU Register lists no authorised health claim for CLA. Naming an isomer is an identity statement, not a health claim, but it still has to be true and it still has to match the specification. In the US, the label follows 21 CFR 101, and a structure/function claim needs the DSHEA disclaimer; a disease claim is not allowed. The compliance page sets out the market routes.
The novel-food and dietary-ingredient routes attach to the oil, not to the three-letter abbreviation. A supplier's statement that “CLA is approved” does not say which isomer mix, which use or which market. Ask for the reference that belongs to the exact oil.
When to choose a mix and when to choose one isomer
Choose a declared mix when the label says “CLA” without naming an isomer, when the supply has to be reproducible across lots, and when the specification can carry a ratio with a tolerance. A mixed oil is the usual commercial material, and it is easier to source and to keep consistent than an enriched fraction. The label then describes the ingredient, and the certificate carries the ratio.
Choose an enriched or single-isomer oil only when the label names that isomer and the project has a specification, a certificate and a supply chain for it. That is a different material with its own lead time, and it needs its own stability and allergen file. The choice is a labelling and supply decision, not a health claim, and it should be made before the artwork is signed off.
If the brand has no isomer story, do not invent one. A label that names an isomer it cannot prove is worse than a label that names the ingredient and lets the certificate carry the detail.
How to write the isomer into the specification
Write the identity as a set of figures: total CLA by GC; c9,t11 and t10,c12 each as a percentage of total CLA and as a percentage of the powder; the ratio with its tolerance; the oil load; the carrier and antioxidant; the mesh; the oxidation limits; the source oil; and the CAS number. State the basis once and use it everywhere. If the certificate reports only the total, the specification is stronger than the file that supports it.
This catalog lists CAS 2420-56-6 for CLA. Registries also assign separate numbers to the individual isomers, so the CAS is a handle for the material, not a statement of the ratio. The CLA powder hub carries the catalog specification, and the COA page lists the lines a certificate should carry.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation