06 Identity & adulteration

How we prove a CLA oil lot is conjugated linoleic acid

Technical document 06 · Reviewed 2026-11-20 · CLA Oil

On this page
  1. The four layers of identity
  2. The isomer ratio and the residual acids
  3. What X-ray diffraction can and cannot show
  4. The routes that matter
  5. What the identity specification should say
  6. Five questions for a supplier

A CLA oil lot is identified by the whole fatty-acid profile, the isomer pair and the esterified form together, not by the CLA figure alone. A concentrate can be diluted to hit a total, an incomplete reaction leaves the total in range with the wrong balance, and a free-acid oil reads like a triglyceride until the acid value is seen. The profile, the split, the form and the paper trail are the evidence, and they have to agree.

In one line

Identity is the whole fatty-acid profile plus the isomer pair and the form, because a CLA figure on its own can be assembled from a different isomer mix or a different feedstock.

The four layers of identity

The right name on a certificate does not prove the material. Each layer below settles something the others cannot; a supplier who stops at the first has described a document.

Four layers of CLA oil identity
LayerWhat it settlesMeasurementWhat it establishes
PaperIs anything named, and at which range?Product name, CAS 2420-56-6, CLA 70.0–80.0%That a document exists, nothing more
ProfileIs this a conjugated C18:2 oil from a linoleic feedstock?GC of fatty acid methyl estersThe family and the residual acids
IsomersWhich conjugated isomers, in what share?GC with isomer resolution; silver-ion HPLC where neededThe isomer distribution
Form and balanceEsterified or free acid, diluted or not?Acid value or free fatty acid, glycerol and sterol patternThe form and the mass balance

The order matters. The profile can be right while the isomer split is different, and the isomer split can be right while the oil has been extended with a cheaper fat. Only the fourth layer catches a change of form.

The isomer ratio and the residual acids

The catalog fixes the two named isomers at ≥90.0% of CLA and leaves the split between them to the certificate. A commercial concentrate made by alkali isomerisation usually returns the two in roughly equal share, while a more selective route can favour one of them. Neither is a defect, but a label that declares one isomer needs the measured split, because “90% of CLA” says nothing about which isomer the serving carries.

The rest of the profile is the second marker. A CLA concentrate is not pure CLA: the balance is other fatty acids, mainly palmitic, stearic and oleic acid together with unreacted linoleic acid. Linoleic is the one to read closely, because it is the substrate. A high residual figure can mean an incomplete conversion, and a figure well below the rest of the profile can mean the concentrate has been blended with a cheaper oil and re-standardised.

Markers to read together on a CLA oil certificate
MarkerWhat the catalog fixesWhat a deviation suggests
CLA as fatty acids70.0–80.0%Below range: dilution or incomplete conversion
cis-9,trans-11 + trans-10,cis-12≥90.0% of CLABelow range: other conjugated isomers present
Split between the two isomersReported, not fixedA shift within range: different process or feedstock
Residual linoleic acidNot fixedHigh: incomplete reaction; very low: a blend
Palmitic, stearic, oleic acidNot fixedA profile that no longer matches the feedstock
Free fatty acid or acid value≤0.50%High: the free-acid form, or hydrolysis

The table is a reading aid, not a second specification: two lines are release limits and four are context, and the context is what makes a substitution visible.

What X-ray diffraction can and cannot show

X-ray diffraction identifies crystalline phases, and CLA oil is a liquid at room temperature with no lattice to diffract. A pattern run on the neat oil is therefore not an identity test: it says the sample was not crystalline, which is already known. The technique earns its place on the powder, where the starch carrier is crystalline enough to give a pattern, and there it describes the carrier rather than the oil.

There is one troubleshooting use. A lot that throws a solid at low temperature can be examined to see what crystallised, which helps to separate a cold-storage effect from a foreign fat. That is an investigation, not a release test, and it does not measure the isomer ratio. Read an “XRD identity” line on an oil certificate as a statement about the wrong instrument unless it says which phase was measured. The XRD method note sets out the limits of the technique.

The routes that matter

CLA oil substitutions and the signals
RouteWhat it doesSignalCheck
Dilution with a cheaper oilLowers CLA per gramCLA at the bottom of the range; profile reshapedFull profile; sterol pattern
Different isomer mixTotal unchanged, distribution movedSplit shifts; label no longer matchesGC resolution; silver-ion HPLC
Incomplete conversionCLA in range, linoleic highResidual linoleic above the usual balanceFull profile
Free acid sold as triglycerideSame CLA figure, different materialFree fatty acid or acid value highAcid value; glycerol
Oxidised oilCLA figure intact, quality gonePeroxide value high; p-anisidine value risingOxidation panel

The first three routes share a feature: the CLA figure can stay within the release range while the oil changes. That is why the profile and the split belong beside the total: a certificate with one number leaves the likely substitution untested. Oxidation is the opposite case: the identity is unchanged and the oil is still failing.

What the identity specification should say

  • “Conjugated linoleic acid oil, CAS 2420-56-6, CLA 70.0–80.0% by GC of fatty acid methyl esters.”
  • “Esterified form stated: triglyceride or free fatty acid, with the acid value or free fatty acid limit.”
  • “cis-9,trans-11 and trans-10,cis-12 ≥90.0% of CLA, with the measured split reported.”
  • “Full fatty-acid profile reported, including residual linoleic, oleic, palmitic and stearic acid.”
  • “Peroxide value ≤5.0 meq O₂/kg; moisture ≤0.1%; appearance clear to slightly hazy.”
  • “No other vegetable oil added; feedstock and process named.”

A specification that says only “CLA 80%” leaves the laboratory no way to check the isomers, the residual profile or the form. The certificate should repeat those lines and carry the lot code that matches the pack and the retained sample.

Five questions for a supplier

  1. Is the CLA esterified as a triglyceride or supplied as free fatty acids, and what is the acid value or free fatty acid result?
  2. What are the cis-9,trans-11 and trans-10,cis-12 figures separately, and can you send the chromatogram?
  3. What are the residual linoleic, oleic, palmitic and stearic figures on the same lot?
  4. Which feedstock and which isomerisation and refining steps were used for this lot?
  5. If the lot is disputed, who attends the re-test, and on which retained sample?

Those five answers build an identity file. One CLA percentage does not. The catalog limits are on the CLA oil product page, the release lines are on the COA page, the grade axes are on the grades page, the powder is specified on the CLA powder page, the methods are indexed under methods, and the retained-sample workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation