02.1 Oil vs powder

CLA oil vs CLA powder: the carrier, the dose and the label

Technical document 02.1 · Reviewed 2026-11-20 · CLA Oil

On this page
  1. The carrier is the real difference
  2. The same label figure in two masses
  3. The isomer pair crosses both products
  4. What the label has to declare
  5. Handling follows the form
  6. When to choose the oil and when the powder

The oil carries 70–80% CLA as fatty acids; the microencapsulated powder carries ≥10% CLA on a starch carrier. The same label figure therefore needs about seven to eight times the powder mass, and the powder brings a carrier that has to be declared. The oil is a fat a formulator can blend into a softgel fill; the powder is a dispersible solid for sticks, dry blends and high-mass formats.

In one line

At 80% CLA the oil carries eight times the CLA of the 10% powder per gram, so the choice is a fill-weight and carrier decision before it is a label decision.

The carrier is the real difference

The oil has no carrier to declare. It is CLA with a small antioxidant package, and everything else in the certificate is the fatty-acid balance. The powder is the opposite: the CLA arrives inside an oil that has been emulsified into a starch matrix and dried, so most of the powder is carrier and moisture rather than CLA. At 10% CLA from an 80% oil, the oil load is about 12.5%, which leaves roughly 87% of the powder as starch, antioxidant and water.

That arithmetic decides what the label says and what the process handles. A modified starch carrier must be declared, and it carries its own allergen and source statement; the oil's antioxidant system is declared too, but there is no bulking agent behind it. The powder specification also carries lines the oil does not: p-anisidine value ≤20.0, a particle size of ≥95% through 40 mesh, and moisture at ≤5.0% against the oil's ≤0.1%.

Read the peroxide value carefully on the powder. The oil limit of ≤5.0 meq O₂/kg is stated on the oil; the powder's limit is stated on the powder, and the units are not interchangeable if one is measured on the powder and the other on the extracted oil. At a 12.5% oil load, a result of 4 meq/kg on the powder corresponds to about 32 meq/kg on the oil inside it. Ask which basis the certificate uses before comparing the two numbers.

The same label figure in two masses

The label declares a mass of CLA. The table converts that figure into product mass at both ends of the oil range and at the powder's catalog minimum.

Product mass needed for a declared CLA figure
CLA declaredOil at 80%Oil at 70%Powder at 10%
300 mg375 mg429 mg3,000 mg
600 mg750 mg857 mg6,000 mg
800 mg1,000 mg1,143 mg8,000 mg

A 1,000 mg softgel filled with the 80% oil delivers about 800 mg of CLA as fatty acids, before the glycerol correction. The same 1,000 mg capsule filled with the 10% powder delivers about 100 mg, so reaching 800 mg from the powder takes about 8,000 mg — roughly seven 1,200 mg capsules. The powder is not a weaker version of the oil; it is a format for products that can carry grams rather than milligrams, such as a stick pack or a dry blend.

Neither column is an intake recommendation. The fill weight, the number of units per serving and the overage are the formulator's decisions, and the arithmetic above is only the conversion between a CLA figure and the mass that carries it.

The isomer pair crosses both products

The oil's catalog line fixes cis-9,trans-11 and trans-10,cis-12 at ≥90.0% of CLA and leaves the split to the certificate. The powder's catalog table lists the total CLA at ≥10.0% and does not carry the isomer line, so a buyer who needs the pair declared has to ask for it and put it in the powder specification. Ten per cent CLA with a 90% pair is at least 9% of the powder mass as the two named isomers.

Both products should report the split, because the arithmetic for a label that names one isomer depends on it, and because a change of feedstock shows up in the split before it shows up in the total. A powder made from an oil with a different isomer distribution is a different label ingredient even when the 10% figure is identical.

What the label has to declare

In the EU the ingredient list carries the oil or the powder with its carrier, the nutrition declaration carries fat and saturates, and the CLA amount is stated per portion from the product mass and the CLA figure. In the US the Supplement Facts panel names conjugated linoleic acid per serving, and the carrier appears in the ingredients list.

The CLA figure needs its basis on both sides: per serving, from the declared product, and on the fatty-acid basis the certificate uses. A “water-dispersible” or “mixes clear” statement belongs to the powder, not to the oil. One point of US nutrition labelling deserves the reviewer's attention rather than an assumption: the trans fat definition covers trans double bonds in isolated, non-conjugated positions, so a conjugated CLA is treated differently from a partially hydrogenated fat. The reviewer confirms the current text before the panel is set.

Handling follows the form

The oil goes into an amber bottle or a nitrogen-flushed drum because oxygen and light are its failure route, and a softgel protects the fill with an opaque shell and a low-oxygen headspace. The powder goes into a foil pouch because moisture and light are its failure route, and the pouch seam is the weak point. Neither pack can be swapped for the other without a new stability file.

At the bench the oil is warmed gently and mixed before weighing, and the bottle is closed between draws; the powder is kept dry, resealed, and trialled in the matrix for taste and for ringing in a beverage. The powder is dispersible rather than soluble, so a clear drink needs an emulsified oil with its own stability data, not a starch powder stirred in.

When to choose the oil and when the powder

Choose the oil for a softgel, an oil blend or a lipid-based fill, where a liquid carrier is wanted and the CLA figure is reached in about a gram of fill. Choose the powder for a hard capsule, a tablet, a stick pack or a dry blend, where a free-flowing solid is needed and a few grams per serving are acceptable.

A switch is a new specification, a new label and a new stability file, not a unit conversion. The oil is specified on the CLA oil product page; the powder is specified on the CLA powder page; the grades page places the two in the wider range; the analytical methods are indexed under methods; and the release workflow is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation