03 Stability

CLA oil stability: oxidation, pack and retest period

Technical document 03 · Reviewed 2026-11-20 · CLA Oil

On this page
  1. The neat oil in its sealed pack
  2. There is no aqueous solution, but there are dispersions
  3. What moves the oil in storage
  4. A stability protocol for the oil
  5. What the finished formula does
  6. How the retest period is set

CLA oil fails by oxidation before the CLA assay moves. The conjugated diene that defines the material is a ready target for oxygen, so peroxide value rises first, p-anisidine value follows as secondary aldehydes form, and free fatty acid climbs when moisture reaches the oil. The pack, the headspace and the storage temperature set the rate, and light passes straight through a clear bottle.

In one line

CLA oil fails at the peroxide value first: the conjugated diene takes up oxygen before the CLA figure moves, so the headspace and the pack decide the shelf life.

The neat oil in its sealed pack

The release limits are peroxide value ≤5.0 meq O₂/kg, free fatty acid ≤0.50% and moisture ≤0.1%. Those are gates at filling, not buffers for storage. Residual water and water vapour both drive hydrolysis, and free fatty acid is the value that climbs; a drum left open in a damp room is no longer in the condition it was tested under.

Oxygen matters more. Oxidation starts at the oil surface and continues in whatever air sits above it, so a full drum ages more slowly than one that has been drawn down. The 1 kg amber bottle and the 25 kg HDPE drum both limit light, and the bottle is the pack that gets opened most often. Nitrogen can displace the headspace at filling, but the flush has to be specified and checked; without a measurement it is an assumption. Once a pack is open, decant the remainder into a smaller container that leaves little air.

Heat raises the rate of every one of those reactions, and a store beside a heater or a drum in a hot loading bay is a different condition from a temperature-controlled room. A winter delivery that arrives cold should be allowed to equilibrate before the pack is opened, so that condensation does not form on the oil.

There is no aqueous solution, but there are dispersions

CLA oil is insoluble in water and is supplied as an oil, so the systems that matter are the ones it is built into: oil blends, oil-in-water emulsions and softgel fills. Each changes the oxidation rate, and none inherits the bulk oil's result.

In a blend the most unsaturated oil usually governs the induction period, so a modest share of CLA can pull a whole blend down. In an emulsion the oil sits in small droplets, the interfacial area is large, and oxygen, light and trace metals meet the oil at the interface; the emulsifier, the pH and the homogenisation energy can matter more than the bulk oil's own peroxide value. In a softgel the shell limits oxygen transfer without stopping it, and it can carry moisture into the fill.

The sibling CLA powder is a different system again: the oil is held in a starch matrix, so the drying step, the oil load and the seal on the pouch decide the rate. A bulk-oil stability file does not transfer to it, and its file does not transfer back.

What moves the oil in storage

What changes CLA oil during storage
FactorEffectControl
OxygenRaises peroxide value, then p-anisidine valueNitrogen flush; low headspace; sealed pack
LightAccelerates oxidation through clear glass or filmAmber bottle or opaque secondary pack
HeatRaises the rate of oxidation and of hydrolysisCool store; short holds; no hot loading bay
MoistureDrives hydrolysis and raises free fatty acidDry store; closed liner; ≤0.1% at release
Metal ionsCatalyse oxidation at trace levelsStainless steel or glass contact; avoid iron and copper
Repeated openingReplaces the headspace with airSmaller packs; decant into a full container

The factors reinforce one another. A warm, lit store holding a part-used drum is the hard case, and the useful question is not whether CLA oil is stable in the abstract but for how long, in which pack, under which condition.

A stability protocol for the oil

A usable protocol fixes four things: container, climate, sampling times and tests. A common design uses long-term storage at 25 °C/60% relative humidity, intermediate storage at 30 °C/65% relative humidity and accelerated storage at 40 °C/75% relative humidity. Add a light-exposure arm, because a dark incubator cannot reveal a photochemical failure.

Test peroxide value, p-anisidine value, free fatty acid, moisture and appearance at every point, and run the full fatty-acid profile and the isomer split at the first and last points. The catalog sets no anisidine limit for the oil even though the powder specification carries one, so agree the line you want before the study starts rather than after the numbers arrive. If the oil goes into a softgel, a blend or an emulsion, study that matrix as well.

Sampling has to be representative. A top-of-drum sample is not the same as one drawn after mixing, and a sample left open on the bench has already started to oxidise. Record how the sample was drawn, how it was held before the test, and how long it waited.

What the finished formula does

A softgel is the usual home for CLA oil. The shell is a barrier rather than a seal: gelatin and plant shells transmit some oxygen and moisture, and the seam is the weak point. Measure the fill at release and at the end of the study, and inspect the shell for discolouration, sticking and leakage. Blended with a more saturated oil the fill may oxidise more slowly than CLA alone, but not as slowly as the saturated oil, and the label declares the blend in descending order by weight.

Any antioxidant is part of the specification. Mixed tocopherols, rosemary extract or another system should be named with its level, because it changes the label and the analytical result. An antioxidant slows oxidation; it does not reverse it. Adding tocopherol to an oil that already sits near the peroxide limit does not restore the specification, and deciding the antioxidant system after a failing result means another stability study.

How the retest period is set

No single shelf life applies to CLA oil, because the pack, the headspace and the storage condition decide it. A retest period has to rest on data from the same pack, and a number published without the pack and the condition is an assertion rather than a shelf life.

Before any extension, the retained sample is re-tested at the end of the period. A bulk result does not transfer to a softgel or to a repacked bottle, and one customer's storage condition does not transfer to another's. The delivery documents should state the lot, the production date and the retest date, and the buyer should confirm the remaining life at delivery.

The catalog specification is on the CLA oil product page, the release tests are described on the COA page, packs and lead time are on the MOQ page, the analytical methods are indexed under methods, and the retained-sample and release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation