02 Grade comparison

CLA oil grades: concentration, form and isomer split

Technical document 02 · Reviewed 2026-11-20 · CLA Oil

On this page
  1. Why CLA oil comes in grades
  2. The grades side by side
  3. Appearance, clarity and handling
  4. Dose arithmetic on the grade
  5. What to write into the specification
  6. When the oil is the wrong grade

CLA oil is quoted as a concentration inside a 70–80% window and in one of two esterified forms, so a grade is that pair of decisions plus the isomer distribution behind it. An 80% oil carries about 14% more CLA per gram than a 70% oil, and a triglyceride oil and a free-acid oil with the same CLA figure behave differently at the balance. The ≥10% powder is a separate product rather than a lower grade of the same oil.

In one line

Grade is a concentration and a form decision before it is a brand name: an 80% oil carries about 14% more CLA per gram than a 70% oil, and the triglyceride and free-acid forms differ in acid value and in the label.

Why CLA oil comes in grades

Commercial CLA is made by conjugating the linoleic acid of a high-linoleic feedstock, usually safflower or sunflower oil, and then concentrating the conjugated fatty acids. The concentration step decides whether the lot sits near 70% or near 80%, and the route decides what the rest of the oil is: unreacted linoleic and oleic acid, palmitic and stearic acid, and a small share of other conjugated isomers.

Two variables travel with the concentration. The first is the esterified form. A triglyceride retains the glycerol backbone, so the oil is a fat with a low free-acid value; a free-acid product has been hydrolysed, carries a high acid value and behaves as a fatty acid mixture rather than as a fat. The second is the isomer distribution: the catalog fixes the two named isomers at ≥90.0% of CLA but not the split between them, so two lots can meet the same line and still differ.

The grades side by side

What changes across CLA oil grades
Property70% grade80% gradeWhy it matters
CLA as fatty acids70.0%80.0%Fill weight per label figure
CLA per gram of triglyceride oilAbout 0.67 gAbout 0.76 gGlycerol takes about 5% of the mass
Residual linoleic and oleic acidHigherLowerProfile shape and oxidation behaviour
Free fatty acid≤0.50% for an esterified oil≤0.50% for an esterified oilA free-acid grade is a different purchase
Isomer pair≥90.0% of CLA≥90.0% of CLAThe split is agreed separately
Peroxide value≤5.0 meq O₂/kg≤5.0 meq O₂/kgOxidation gate, not a grade marker

The two columns are not a ranking: a 70% oil is not a defective 80% oil. What changes is how much oil the formula needs and how much residual fatty acid arrives with it. A buyer who specifies “CLA 80%” and accepts 70% at the intake has taken a different product without redoing the fill weight.

The form deserves its own line on the purchase order. A triglyceride and a free-acid CLA are both described as “CLA oil”, and the certificate looks similar until the acid value is read. Ask for the form in writing, and put the acid value or the free fatty acid limit beside it.

Appearance, clarity and handling

The catalog appearance is a clear to slightly hazy oil, pale yellow in the usual refined grade. Colour is a weak quality signal: refining and storage both move it, and a darker oil can still meet the CLA and oxidation limits while a pale one can be part-way through oxidation. Clarity is more useful as a handling note than as a specification.

CLA is insoluble in water and soluble in fats and organic solvents, so it mixes into oil blends and softgel fills without an emulsifier. Some CLA isomer mixtures thicken or cloud at refrigerator temperature; the change reverses on gentle warming and is not an identity failure, but a customer who stores the oil cold should agree how it is handled. Warm the container gently and mix before weighing, and keep it closed between draws.

Dose arithmetic on the grade

The label declares a mass of CLA, so the grade sets the oil mass that carries it. The table works the arithmetic at both ends of the catalog range, before the glycerol correction.

Oil mass needed for a declared CLA figure
CLA declaredAt 70% CLAAt 80% CLANote
350 mg500 mg438 mgSmall softgel range
700 mg1,000 mg875 mgSingle 1 g fill
1,000 mg1,429 mg1,250 mgAbove a standard 1 g fill

These are label figures, not intake recommendations. Two corrections sit behind them. The glycerol correction applies when the oil is a triglyceride: the fatty-acid figure is not the oil mass, so 875 mg of an 80% triglyceride oil delivers about 665 mg of CLA, and the fill has to rise to about 921 mg to reach the declared 700 mg. The isomer correction applies when the label names one isomer: a c9,t11 declaration needs the measured split, because the catalog fixes only the sum of the two.

An overage is a third, separate decision. It is the extra material added so the label claim still holds at the end of the shelf life, and it is justified by the stability curve for the pack, not by the grade. Do not fold an overage into the grade conversion; a lot at the top of the range is not an overage.

What to write into the specification

  • “Conjugated linoleic acid oil, CAS 2420-56-6, CLA 70.0–80.0% by GC.”
  • “Esterified form: triglyceride or free fatty acid, stated on the certificate.”
  • “cis-9,trans-11 and trans-10,cis-12 ≥90.0% of CLA, with the split reported.”
  • “Free fatty acid ≤0.50%; peroxide value ≤5.0 meq O₂/kg; moisture ≤0.1%.”
  • “Appearance clear to slightly hazy; heavy metals and microbiology as listed.”
  • “Grade, pack and destination market confirmed before the order.”

A specification that names only “CLA 80%” has fixed one of the three axes. The form and the isomer split are the other two, and they are the ones a substitute lot will differ on.

When the oil is the wrong grade

A dry blend, a tablet or a stick pack cannot take an oil at the inclusion the label needs, which is why the microencapsulated powder exists at ≥10% CLA on a starch carrier. Choosing the powder is a change of product, not a change of grade: the carrier is declared, the dose arithmetic moves by a factor of about eight and the oxidation route changes. The comparison is set out on the oil against powder page.

Within the oil, the wrong grade is usually a concentration mismatch. A formula built on 80% and supplied at 70% underdelivers unless the fill weight is recalculated, and a formula built on 70% and supplied at 80% overdelivers. If the market file or the customer specification names one concentration, the catalog range is not a licence to ship any point inside it.

The catalog specification is on the CLA oil product page. The release lines are on the COA page, the oxidation behaviour is on the stability page, the powder is specified on the CLA powder page, the methods are indexed under methods, and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation