06 Identity & adulteration

How we prove a superoxide dismutase lot is the enzyme it names

Technical document 06 · Reviewed 2026-11-19 · Superoxide Dismutase

On this page
  1. The four identity layers
  2. The copper-to-zinc ratio
  3. What X-ray diffraction and infrared can show
  4. What adulteration looks like
  5. What to write into the identity specification
  6. Five questions for the supplier

A superoxide dismutase lot is identified when four measurements agree: the catalytic activity in a defined assay system, the protein content and pattern, the metal at the active site, and the lot record that ties the pack to the concentrate and the carrier. The activity alone is not enough, because a blend, a coloured plant extract or a small-molecule mimic can all produce inhibition in the assay without being the enzyme. Each layer answers a different question, and a supplier who answers only the first has described a number, not a material.

In one line

Identity is the agreement between activity, protein, metal ratio and lot record, because the assay alone can be satisfied by a blend or a mimic.

The four identity layers

None of the four layers is decorative. The document names the material; the assay shows catalysis; the protein measurements show that a protein is present and how large it is; the metal measurement shows which family of SOD the protein belongs to. A certificate that reports appearance and activity but nothing else has left the most likely substitution untested.

Four layers of superoxide dismutase identity
LayerQuestionTestWhat it proves
DocumentIs the material and source named?Name, CAS number, source, specification versionPaperwork only
ActivityIs there SOD catalysis?Xanthine oxidase and NBT, 50% inhibitionCatalysis, not the protein
ProteinIs a protein present, and which?Kjeldahl or colorimetric protein; SDS-PAGE; infrared amide bandsA protein and its size pattern
MetalWhich SOD family?Copper, zinc, manganese and iron by ICP-MSThe active-site metal

The copper-to-zinc ratio

The common food-grade SOD is the copper-zinc enzyme. Each subunit carries one copper and one zinc, so a pure preparation shows the two metals at roughly equal molar amounts, and each is about 0.4% of the protein by mass. A lot that shows copper without zinc, or manganese alongside copper, is either a different enzyme family or a blend of two.

The manganese enzyme is a tetramer with manganese at the active site and no copper or zinc; the iron enzyme carries iron. The metal panel therefore separates the families before any activity figure is discussed. A further check is available in the assay itself: the copper-zinc enzyme is inhibited by cyanide, and the manganese enzyme is not, which is a simple way to test a claim that a powder is the copper-zinc type.

On a formulated powder the arithmetic is less friendly. At 10,000 U/g the protein is a small fraction of the mass, so the copper and zinc figures land in the low milligrams per kilogram, close to what a carrier can contribute on its own. Run the metal panel on the concentrate where possible, and run the carrier as a blank; a metal ratio read on a diluted powder without a blank is not evidence.

What X-ray diffraction and infrared can show

A protein powder is amorphous, so its X-ray diffraction pattern is a broad halo rather than a set of sharp reflections. That limits what the method can say about identity, but it does not make it useless: a sharp pattern in a powder that should be amorphous points to a crystalline diluent, an inorganic filler or a mineral carrier that the specification does not name. Ask for the pattern and the reference, not a line that says “XRD conforms”.

Infrared spectroscopy is the more useful of the two here, and it is the method named on the catalog identification row. A protein gives amide bands, and the carrier gives its own fingerprint, so the spectrum shows whether a protein is present and which carrier it sits in. It does not tell SOD from another globular protein; that is the assay's job. Read the two together.

What adulteration looks like

Substitutions and the signals that expose them
SubstitutionWhat it doesSignal
Carrier with a low enzyme loadActivity below the labelLow activity, low protein, low copper and zinc
Another proteinProtein present, no SOD catalysisActivity absent; gel pattern does not match
Blend with another enzymeA second activity in the powderAssay the second enzyme; the SOD number describes one component
Polyphenol-rich extractApparent inhibition of the dyeActivity without protein or metal; matrix interferes with the assay
Small-molecule mimicCatalysis with no proteinProtein assay and gel show nothing at the expected size

The polyphenol case is the one that catches buyers. Many plant extracts reduce or inhibit the tetrazolium dye directly, so they read as SOD activity in the assay without containing the enzyme. A protein figure and a metal panel settle it, and a plant extract sold as SOD should always be accompanied by both.

What to write into the identity specification

  • “Superoxide dismutase, CAS 9054-89-1, source named, activity ≥10,000 U/g with the unit definition.”
  • “Identification by activity assay and infrared spectrum, with the reference spectrum.”
  • “Protein content by a named method; SDS-PAGE pattern reported for the concentrate.”
  • “Copper and zinc by ICP-MS, with the carrier run as a blank.”
  • “No other enzyme declared unless specified; no carrier outside the declared one.”
  • “Lot code on the pack, the certificate and the retained sample.”

Five questions for the supplier

  1. Which source is this lot, and does the certificate name it?
  2. What is the activity, on which assay system, and at what inhibition level was the sample read?
  3. What is the protein content and the specific activity of the concentrate behind the blend?
  4. What are the copper and zinc results, and was the carrier analysed as a blank?
  5. Will you supply the gel image and the infrared spectrum, and accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. The product page carries the catalog specification; the COA page shows where each figure sits on the certificate; the unit page takes the assay definition apart; the catalase page covers the enzyme most often blended with this one; the method notes and the quality page carry the laboratory detail.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation