02 Activity grades

Serratiopeptidase grades: units per gram and what carries them

Technical document 02 · Reviewed 2026-11-19 · Serratiopeptidase

On this page
  1. Why an enzyme is not sold as a percentage
  2. What a grade fixes, and what moves when it changes
  3. Appearance, solubility and the 40 mesh powder
  4. Units, fill weight and the label
  5. Specification lines for this grade
  6. When not to switch grade

Serratiopeptidase is sold by declared activity, not by purity. The catalog grade is a white to off-white powder at ≥20,000 U/g by the casein Folin assay, with ≥95% through 40 mesh and a granulated form available on request. The grade decision is the activity per gram, the material that carries it and the physical form the process can handle.

In one line

Two powders can both be labelled serratiopeptidase and still differ in units per gram, carrier, mesh and the process step their activity survives.

Why an enzyme is not sold as a percentage

A mineral salt can be sold at 98% or 99% because the assay weighs the molecule against everything else in the drum. An enzyme preparation cannot be described that way. The powder contains the enzyme, the remains of the fermentation and any carrier used to standardise the activity, so the useful description is a declared number of units per gram plus the identity of what carries them.

Standardisation is the step that creates a grade. The fermentation and recovery steps produce a concentrate, and the concentrate is either sold as it is or diluted to a declared activity. Two powders at the same units per gram can therefore hold different amounts of enzyme protein, and two powders with the same protein content can be sold at different activities. Both facts matter when a formula is built around a fixed fill weight.

The unit definition travels with the grade. A preparation at 20,000 U/g by one method and a preparation at 20,000 U/g by a method with a different pH or temperature are not the same article, even when the certificates look alike. The assay glossary sets out why the substrate and conditions belong in the specification.

What a grade fixes, and what moves when it changes

A grade is a bundle of properties rather than a single number. The first table lists what the bundle contains; the second lists what a switch actually changes in the formula.

Properties that a serratiopeptidase grade fixes
PropertyWhat it controlsWhere it shows up
Activity (U/g)Units delivered per gram of powderFill weight, capsule size, label declaration
CarrierWhat the activity is standardised onIngredient list, excipient load, flow
Particle sizeFlow, dust and blend uniformityMixing time, capsule filling, sieving
Physical formPowder or granuleDust control, wetting, dissolution
Source strainWhich organism produced the enzymeIdentity file, regulatory dossier
Unit definitionWhat the number meansCertificate, specification, comparability
What changes when the grade changes
ChangeEffect on the formulaWhat to re-check
Higher activity per gramLess powder for the same unitsCapsule size, blend ratio, content uniformity
Lower activity per gramMore powder for the same unitsFill weight, excipient space, label
Different carrierNew ingredient on the labelAllergen and carrier statements
Granulated instead of powderBetter flow, different wettingBlend time, dissolution, assay after granulation
Different assay methodThe same number means something elseComparability, specification, certificate

A blend is not a grade. A powder that reaches 20,000 U/g by adding another protease has the activity but not the identity, and the certificate will show it only if the method and the protein pattern are examined. The identity page covers the tests that separate a standardised single enzyme from a blend.

Appearance, solubility and the 40 mesh powder

The catalog powder is white to off-white and free-flowing, and it dissolves in water to a clear to slightly turbid solution. The turbidity is normal for a protein preparation. A solution that is heavily cloudy or leaves a sediment may point to a carrier that does not dissolve or to a poorly milled lot.

The particle-size line, ≥95% through 40 mesh, is a finishing specification. It matters for blend uniformity and for capsule filling, and it can move when the mill or the sieve changes without any change in the enzyme. A granulated form is available on request; granulation improves flow and reduces dust, but the wet mass and the drying step add a heat and moisture load that the activity has to survive. Ask for the activity result after granulation, not only on the ungranulated powder.

Colour tells the buyer very little about activity. A whiter powder can be a dilution and a slightly darker one can be a concentrate. The number on the certificate, with its method, is the only reliable statement about strength.

Units, fill weight and the label

The arithmetic is simple and worth doing before a grade is chosen. At 20,000 U/g, one gram carries 20,000 U and one milligram carries 20 U. A 250 mg capsule of this grade carries 5,000 U. If the formula needs 20,000 U in a single capsule, that capsule needs one gram of this grade, or a smaller weight of a higher-activity grade.

That is why a dilution can break a dosage form. Halving the activity per gram doubles the powder mass for the same units, and the extra mass has to fit the capsule, the stick pack or the tablet. The carrier also enters the ingredient list, and the label has to declare it. A switch in grade is therefore a change to the fill weight, the excipient load and the label at the same time.

An enzyme activity is not a nutrient with a Daily Value. If the label states the activity, it should state the unit and the basis, and the destination's labelling rules decide whether the figure belongs in the supplement panel or beside it.

Specification lines for this grade

  • “Serratiopeptidase, CAS 37312-62-2, EC 3.4.24.40, from Serratia marcescens.”
  • “Activity ≥20,000 U/g by the casein Folin assay, with the pH, temperature, incubation time and unit definition stated.”
  • “Identification by IR spectrum, conforming to the reference, and by the activity assay.”
  • “Loss on drying ≤5.0%; heavy metals and microbiology as listed.”
  • “Particle size ≥95% through 40 mesh; carrier and granulation declared.”
  • “No other protease activity declared; any blend is named as a blend.”

We supply the 20,000 U/g powder and a granulated form on request. A different activity per gram is a different specification and should be quoted as such, with its own certificate and its own stability data. The catalog figures are on the product hub, and the release tests are on the COA page.

When not to switch grade

A grade switch is the wrong move when the label has already been approved around a named activity and unit definition. The new powder may meet the same number on paper and still fail the label review, because the method behind the number has changed.

It is also the wrong move when the only reason for the switch is a lower powder mass. A higher-activity grade can reduce the fill weight, but it also changes the blend ratio and the content uniformity, and the process has to be revalidated. The comparison with nattokinase shows why a unit from another protease cannot be substituted for this one, and the quality page describes how a specification change is controlled.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation