03 Stability

Phytase stability: heat, moisture and the pack

Technical document 03 · Reviewed 2026-11-20 · Phytase

On this page
  1. The powder: moisture, temperature and time
  2. The solution: the shortest shelf life
  3. The variables that cost activity
  4. Designing the stability study
  5. What the finished formula does to the data
  6. Where the shelf-life figure comes from

Phytase is a protein, so its activity falls as heat, moisture and time act on it. A sealed powder at ambient temperature holds its activity for months; an open pouch in a humid room loses it faster; a solution made on site from the powder loses it within days; and pelleting is usually the largest single loss in a feed mill. The shelf-life figure comes from stability data on the exact pack and storage condition, and the release certificate does not supply it.

In one line

Heat and moisture are what consume phytase activity; the pack, the process temperature and the time on the shelf decide how much is left.

The powder: moisture, temperature and time

The catalog sets loss on drying at ≤8.0%. That limit is checked at release, and it is also the room the lot has left for moisture pick-up. A pouch opened in a humid room takes water from the air, the loss on drying rises, and the activity per gram of powder falls because the powder is now carrying inert water. The enzyme may be undamaged and the number on the re-assay will still be lower.

Temperature acts on the protein itself. Every enzyme has a rate of inactivation that climbs with temperature, so a pallet parked in a hot loading bay or a drum stored beside a heater ages faster than the same lot in a cool store. Ambient warehouse conditions are usually acceptable for a sealed pack; a car boot, a greenhouse or a sun-exposed container is not.

The pack, not the certificate, is what keeps moisture out. The 1 kg foil pouch and the lined 25 kg fiber drum both do that while they stay closed. Folding an opened pouch over does not make it heat-sealed again, and the air it traps is humid. For long storage, decant the remainder into a smaller sealed container and write the opening date on it.

The solution: the shortest shelf life

The catalog product is a powder. Liquid phytase preparations exist, and they are formulated for stability with a stabiliser and a preservative, but a solution made in the plant from the powder is a different proposition. Once the enzyme is in water, heat, pH and microbial growth act at the same time, and activity can fall quickly at room temperature.

If a liquid addition is needed, make it fresh, keep it cool, control the pH and use it within the validated hold time. Avoid high shear and foaming, which denature protein at the air interface, and keep the tank covered. The assay pH of 5.5 is a measurement condition, not a stability optimum: the formulation's own pH and the time in the tank have to be tested.

Post-pellet liquid application is a common way to avoid the heat of the press, and it moves the stability question to the finished feed. The coated pellet still has a moisture and temperature history, and the activity in the feed has to be measured rather than calculated from the tank assay.

The variables that cost activity

Factors that move phytase activity in storage and processing
FactorWhat it doesControl
HeatDenatures the protein; the main loss in pelletingCool store; validated conditioning and press conditions
MoistureDilutes the powder and accelerates inactivationSealed pack; dry store; closed liner
pHMoves the enzyme away from its active rangeValidate the matrix pH; do not assume the assay pH
Proteases and microbesDigest the enzyme in a wet matrixPreservative and hygiene control in liquid systems
Metal ionsCan bind or inactivate the proteinCheck premix compatibility; avoid direct contact
Shear and foamDenature protein at the air-liquid interfaceLow-shear mixing; avoid over-agitation
TimeProgressive loss at any conditionEnd-of-shelf-life minimum; retest at the stated interval

These factors combine. A warm, humid premix line is worse than either condition alone, and a liquid held in a warm tank combines heat, pH and microbial growth. The useful question is not whether phytase is stable, but how much activity remains in this pack, after this process, at this point in the shelf life.

Designing the stability study

The study design names the pack, the chamber condition, the sampling points and the test panel. The chamber conditions are 25 °C and 60% relative humidity for long-term, 30 °C and 65% for intermediate, and 40 °C and 75% for accelerated. Together they show how the pack behaves in a warehouse and under stress. The report should give the result at each point rather than a single verdict, and name the pack and the lot family.

Test activity by the named sodium-phytate method at every point, with loss on drying, appearance and microbiology. The activity figure needs the same blank and standard curve as the release assay, or the trend is noise. If the material will be pelleted, add a process arm: condition and press at defined temperatures and residence times, then assay the pellets, because the press is a harsher test than any incubator.

The data to request is the one for the pack you will actually buy. A drum and a pouch differ in headspace, opening history and surface-to-volume ratio, so one pack's result does not describe the other.

What the finished formula does to the data

A premix is not an inert carrier. Trace minerals, choline chloride and acidic ingredients can hold moisture against the enzyme, and a premix with a high mineral load can lose activity faster than the powder alone. Ask for compatibility data, or run a small blend and assay it after the intended storage period.

In a compound feed, the mash and the pellet are different products. The mash carries the enzyme through the mixer; the pellet carries it through steam and pressure. Post-pellet application avoids the press but adds a liquid-handling step. Whichever route is used, the activity in the finished feed is the number that matters, and it is measured, not inferred from the inclusion rate.

An overage is a formulation decision. It can cover a measured process loss, but it cannot rescue a pack that admits moisture, and it should be supported by the process data rather than a fixed percentage carried from another product.

Where the shelf-life figure comes from

No single shelf-life number is published for phytase: the pack and the storage condition are what determine it. The retest period is written on the specification and backed by the stability file for that pack. A figure quoted without the pack, the storage condition and the test panel is not a shelf life.

At the end of the retest period, assay the retained sample again before extending use. An extension needs data, and a bulk figure does not transfer to a repacked container. Standard packs are listed on the product hub. The COA page covers release tests, the MOQ page pack and lead time, the methods library the activity assay, and the quality page the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation