03 Stability

Nattokinase activity falls with heat and moisture; the process decides the shelf life

Technical document 03 · Reviewed 2026-11-19 · Nattokinase

On this page
  1. The dry powder in its sealed pack
  2. Once water is added, the clock runs faster
  3. What drives the loss
  4. A stability protocol that answers the question
  5. Granulation, tableting and the pack
  6. Assigning the shelf life

Nattokinase is a protein, and its declared activity is the property most sensitive to heat, water and pH. A dry powder in a sealed foil pouch holds activity far longer than the same powder wetted, heated or left open. The process step that adds heat or water usually removes more activity than the storage that follows, which is why a shelf life belongs to a process and a pack rather than to a powder on its own.

In one line

A sealed pack holds nattokinase; heat, water and the process step that adds them decide how much activity is left at the end of shelf life.

The dry powder in its sealed pack

At low water activity the enzyme is close to inert: molecular motion is limited, and the reactions that destroy activity need water. The catalog limits — loss on drying ≤8.0% and pH 6.0–8.0 — describe a powder dry enough and neutral enough for ambient handling. A foil pouch or lined drum at ambient temperature holds activity for a long time; the loss over months is small next to one wet process step.

Two habits protect that state. Keep the pack closed until the batch is ready; the powder is hygroscopic, and an open pouch in a humid room picks up water quickly. Read the loss-on-drying result as a release gate, not a storage specification; the loss-on-drying note explains what the figure does and does not say. Refrigeration is no substitute for a dry pack: a cold pouch opened in a warm room condenses water on the powder.

Moisture feeds microorganisms. The micro specification — APC ≤10,000 cfu/g, yeast and mould ≤100 cfu/g, E. coli and Salmonella absent — is a release gate, not a licence to store damp.

Once water is added, the clock runs faster

In solution the protein is fully hydrated, and activity declines even at room temperature. The pH matters: the catalog solution sits at 6.0–8.0, and moving outside that window, or holding it warm, increases the loss. A drink mix is usually a dry powder, so test the mix, not the drink; a ready-to-drink application needs its own data and hold time.

If a process uses a liquid intermediate — a coating suspension, a granulation fluid or a slurry — the time and temperature belong in the process record. A short, cold contact is not an overnight hold, and the activity after the step is what the tablet or granule carries. A wet line not dried before the next run leaves the enzyme in water longer than planned.

What drives the loss

Nattokinase activity · factors and controls
FactorEffectControl
Heat above about 45–50 °CProtein unfolds; the loss is largely irreversibleKeep process temperature low and time short
WaterMobility, caking, microbial growthDry to ≤8.0% LOD, foil pack, desiccant
pH outside 6.0–8.0Activity falls away from the working windowCheck the matrix pH, not only the powder
Wet granulationWater plus binder plus drying heat in one stepLow-water binder, short low-temperature dry
Tablet compressionLocal heat and shear at the punchDirect compression; measure activity in the tablet
Metal ions and oxidantsProtein oxidation and loss of activityScreen the mineral salts and the antioxidant system
LightSlow contributionOpaque pack or carton
Time and opening the packBackground loss; humid air enters the headspaceReal-time data; reseal, desiccant, small packs

The table is qualitative: the size of each effect depends on the matrix.

A stability protocol that answers the question

Run real-time storage at the label condition, with an accelerated arm beside it: 25 °C and 60% relative humidity for real time, 40 °C and 75% for the accelerated arm, with points at 0, 1, 3, 6, 12 and 24 months. For a tropical market, add 30 °C and 65% or 75%. The assay is FU/g by the release method, plus loss on drying, appearance and microbiology.

Test what the customer buys: the tablet, not the powder, or the sealed stick, not the blend. The press adds heat and shear, and the excipients bring their own pH and water. Where a process step is planned, assay the blend before and after it, so the process loss is measured rather than assumed.

Report the result as a percentage of the initial activity as well as the absolute figure. The percentage shows the size of the drop; the absolute figure alone hides whether it came from the material or the starting point. Include a 4 °C control to separate instability from assay drift.

Accelerated data is a screening tool, not a shelf-life claim. A lot that loses activity at 40 °C may still be acceptable at 25 °C, and a lot that passes the accelerated arm can fail in real time. The shelf life rests on real-time data for the pack and matrix; the accelerated arm flags a formula early.

Granulation, tableting and the pack

Wet granulation combines the two factors that remove the most activity: water and heat. A water granulation with a hot dry can remove a large share of the activity before the tablet exists, and the loss is invisible in the powder certificate. Dry granulation avoids the water but adds pressure and heat; direct compression avoids both but still exposes the powder to punch heat and shear.

Coating is a separate risk. Aqueous film coating wets the tablet and dries it with hot air; an organic coating avoids water but brings solvent handling. Effervescent systems are the least friendly matrix, because the tablet is designed to dissolve in water. Stick packs and sachets are friendlier, provided the foil and seal keep water out. The custom processing page sets out how a trial is scoped.

The pack is part of the formula. A foil laminate with a sealed seam, a desiccant where needed and a nitrogen flush for a sensitive blend all change the shelf life. A fiber drum needs a food-grade liner intact at the rim; without it the drum is a shipping container, not a moisture barrier. A pack change is a stability change and needs its own data.

Assigning the shelf life

The label activity is an end-of-shelf-life figure. If the label declares 20,000 FU/g and the study shows 85% retention at the target shelf life, the release target has to sit near 23,500 FU/g for the label to remain true at the end. That is arithmetic, not a batch result; the retention figure comes from the study on that matrix and pack.

Where retention is unknown, the shelf life should be short and justified. One lot is not a shelf life: three lots show the spread, and a single lot can be unusually good. The storage statement — cool, dry, sealed — is part of the claim, and a label that promises a shelf life the pack cannot deliver is a specification error.

The COA page shows the rows the study follows; the grade page explains why a dilution carries more carrier into the matrix; the ordering page covers the packs. The catalog limits are on the nattokinase product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation