How we prove a nattokinase lot has the declared activity
A nattokinase lot is identified by four layers that have to agree: the natto source, the protein, the FU activity and the lot record. The activity figure is the first check buyers make and the weakest alone: a powder can carry the declared FU/g and still be a different preparation.
A nattokinase lot is identified when the natto source, the protein, the FU assay and the lot record agree, and the activity figure alone carries none of those.
Four layers, one claim
Layer one is the source: Bacillus subtilis natto, the strain, the soy material and origin. Layer two is the protein: protein content and gel band pattern. Layer three is the activity: FU/g by the named method, as-is, with substrate and conditions. Layer four is the record: lot code, certificate, retained sample and audit trail.
| Layer | Question | Evidence |
|---|---|---|
| Source | Is it from Bacillus subtilis natto? | Strain statement, soy origin, supplier declaration |
| Protein | Is the protein nattokinase? | Protein content, gel band pattern, specific activity |
| Activity | Does it act on fibrin as declared? | FU/g with substrate, conditions and method |
| Record | Is this the lot tested? | Lot code, COA, retained sample |
No layer carries the claim alone. A source declaration without activity describes a fermentation; an activity figure without a source describes a powder; a certificate without a lot code describes no drum.
The activity assay
The assay incubates a dilution of the powder with a fibrin substrate at a stated pH and temperature, stops the reaction, and measures the change — absorbance at 275 nm in the common method, tyrosine colour in another, or lysis area on a fibrin plate. The result is divided by enzyme charge and time to give FU per gram. Blank, duplicate and calibration turn colour into a number.
Every step is a variable. A different fibrin preparation changes the substrate, a different incubation time moves the reading along a partly linear curve, and a different detection step changes the scale. Two laboratories can both report “20,000 FU/g” and measure different things, so the method reference belongs in the specification.
The assay is not identity. A fungal or another bacterial protease can act on fibrin and return an FU figure. The assay says the powder has fibrin-directed activity, not which protein produced it.
What FU means, and what it does not
The common trade definition is an absorbance increase at 275 nm of 0.01 per minute. Other sheets use 1 µg of tyrosine released per minute, or a lysis area on a fibrin plate. These are not three names for one number; the EU novel-food entry cites Takaoka et al. (2010), a reminder that a unit can be defined by reference to a paper.
An FU figure is per gram of preparation as sold, not per gram of protein or a purity percentage. That is why loss on drying sits beside it: a wetter powder carries fewer FU per gram. A certificate saying only “FU/g” leaves the buyer guessing which FU was used. The FU versus IU page sets out the unit systems and the conversion risk.
Protein, source and strain
Nattokinase is a serine protease of about 275 amino acids and 27–31 kDa, produced by Bacillus subtilis natto. The catalog material carries CAS 9014-01-1 and EC 3.4.21.62. The strain matters: “Bacillus subtilis natto” is a fermentation tradition, not a single genetic line, and the file should name it. Soy is an Annex II allergen in the EU and UK and a major allergen in the US, so the source is declared.
The activity-to-protein ratio
Specific activity is FU per milligram of protein, from the same lot as the FU/g result. Dilution lowers FU/g and protein together, so the ratio holds while the absolutes fall; heat damage lowers FU/g and leaves most protein in place, so the ratio falls; added non-enzyme protein raises the denominator without raising activity. Within one grade and supplier it should sit in a stable band. It is a consistency check, not a purity claim, because the protein method counts all soluble protein while the FU assay counts only fibrin-directed activity.
XRD, and why it is not an identity test here
Nattokinase arrives as an amorphous fermentation powder, so its diffractogram is a broad halo with no sharp reflections from the enzyme. XRD cannot distinguish it from another Bacillus protease, confirm the natto strain or measure FU. Peaks that do appear belong to a crystalline carrier, salt or mineral contaminant, describing the formulation, not the protein. Protein crystallography needs a purified single crystal, not a production lot.
The identity set here is the FU assay with its substrate and conditions, protein content and specific activity, and an electrophoretic band pattern in the 27–31 kDa region against a reference lot.
The routes that pass a weak test
| Route | What passes | What detects it |
|---|---|---|
| Dilution with carrier | Declared FU/g if the blend is assayed | Carrier declaration, mass balance, specific activity |
| Other protease | FU/g on fibrin | Protein band pattern, source-specific test |
| Inactivated powder | Protein content | FU/g and specific activity |
| Overstated activity | A certificate figure | Independent assay with the named method |
| Carrier substitution | Specification sheet unchanged | Carrier identity, change-control notice |
| Mislabelled lot | Certificate belongs to another drum | Lot code on pack, certificate and sample |
The table is a list of checks, not accusations. Most lots are what the certificate says; a buyer who checks only FU/g has one layer of four.
How to write the specification
- “Nattokinase, enzyme preparation from Bacillus subtilis natto, CAS 9014-01-1, EC 3.4.21.62.”
- “Activity ≥20,000 FU/g by the named method, as-is basis, with the substrate, pH, temperature and detection step stated on the COA.”
- “Protein content and specific activity reported; band pattern on request.”
- “pH 6.0–8.0 in 1% solution; loss on drying ≤8.0%; ≥95% through 40 mesh.”
- “Heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg; APC ≤10,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent.”
- “Carrier and any other enzyme activity declared; no undeclared diluent.”
“No undeclared diluent” is doing real work. A lower-activity grade is a legitimate dilution, but the carrier belongs in specification and certificate. The catalog figures are on the product page, and the release workflow on the quality page.
Five questions for a supplier
- Which strain produced this lot, and is the soy material non-GMO?
- What exactly does your FU definition mean, and what are the substrate, pH, temperature, time and detection step?
- Is the result on an as-is or dried basis, and what was the loss on drying for that lot?
- What are the protein content and the specific activity, and what method produced them?
- What carrier or other enzyme activity is present, and where is it declared?
If the second answer is “the standard method”, ask for the method sheet. If the fifth is “none”, ask for the mass balance. Five written answers give a buyer material to audit; one answer gives a number. The COA page shows where each answer sits; the grades page covers the dilution arithmetic.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation