06 Identity & adulteration

How we prove a maltase lot has the declared activity

Technical document 06 · Reviewed 2026-11-20 · Maltase

On this page
  1. What has to line up
  2. Read three ratios together
  3. XRD sees the carrier, not the enzyme
  4. Six failure modes and their signals
  5. Specification lines that can be tested
  6. Five questions for the supplier

A maltase lot is identified by what it does, not by a spectrum: the preparation, the maltose assay, the protein figure and the lot trail have to agree. Activity alone can be produced by a dilution, a different glycosidase or a glucose-spiked powder. The assay conditions and the blank are part of the identity.

In one line

Identity for maltase is a functional claim: the maltose assay, the protein behind it and the lot trail have to agree on the same powder.

What has to line up

Four separate questions sit behind one certificate. Does the document name the preparation — organism, CAS number, carrier and form? Does the assay show the declared rate on maltose? Is that rate carried by protein rather than by sugar already in the powder? Does the lot code on the pack match the code on the certificate and the retained sample? Every question needs its own evidence; an answer to the first alone describes documents, not material.

Four identity questions and the evidence for each
QuestionWhat it rules outEvidence
Is the preparation named?A different material under the same labelOrganism, CAS, carrier, form
Does it act on maltose?A figure from another methodU/g result, substrate, pH, temperature
Is the rate protein-borne?Dilution or a glucose spikeProtein, specific activity, blank
Is this the right lot?A genuine certificate for another drumOne code on COA, pack and sample

Read three ratios together

The first is measured activity against declared activity. A lot declared at 100,000 U/g with a 104,000 U/g result sits at 104% of label. That tells the buyer how much margin the lot has over the floor; it does not tell them the enzyme is the right one.

The second is activity per milligram of protein. Specific activity is a property of the preparation, so it falls when a powder is extended with carrier and rises when the active protein is concentrated. A normal U/g with an unusually low protein figure points to a purified or a spiked material. A normal U/g with an unusually high protein figure means the specific activity is low, which can point to dilution with a protein carrier or to partial inactivation.

The third is the blank against the test signal. The assay measures glucose released from maltose, and glucose already present in the powder or carrier adds to that reading. If the blank is a large share of the response, the U/g figure is partly a sugar measurement. Ask for the blank value and the standard curve, not only the final activity.

A fourth comparison is as-sold against dry basis. At 8.0% loss on drying, the dry-basis figure is about 8.7% above the as-sold figure. Comparing an as-sold result with a dry-basis limit can wrongly reject a compliant lot.

XRD sees the carrier, not the enzyme

X-ray diffraction cannot identify a maltase preparation. The active protein sits on a carrier, and the solid is amorphous; its diffractogram is a broad halo rather than a set of sharp peaks. Sharp peaks point to the carrier or to a mineral filler; a clean diffractogram is silent on enzyme content.

Its only useful job here is to detect a crystalline mineral phase above the detection limit. That is worth knowing when a mineral carrier is suspected, but it is not an identity test for the enzyme. Functional evidence comes from three places: the maltose assay, the protein figure and the organism statement. A heat-hold check adds a fourth by showing that the activity behaves like the expected protein.

Six failure modes and their signals

Failure signatures and the check that exposes each
FailureHow it showsTest
Carrier dilutionA low activity and a low protein figure per gramActivity and protein read together
Glucose or syrup addedA high activity result with a large blankBlank, sugar screen, specific activity
Glucoamylase blendMaltose is split, but the heat profile differsProtein pattern, heat hold, pH profile
Heat-inactivated lotNormal powder, weak activity for its protein loadActivity against protein
Carrier substitutionThe sheet is unchanged while the powder is notCarrier identity, change notice
Lot mix-upThe codes disagree across the documentsOne code on pack, COA and sample

Maltose is not a private substrate. Glucoamylase and some other glycosidases also hydrolyse it, so a maltose-based assay is evidence of maltose hydrolysis, not of one enzyme's presence. A coupled glucose assay does not distinguish which enzyme released the glucose either. For substitution, a heat hold and a pH profile are fast discriminators, because the wrong enzyme usually has a different working window.

Specification lines that can be tested

Nine lines: the activity and its method; identity by assay; protein or specific activity; moisture at ≤8.0%; mesh at ≥95% through 80 mesh; carrier; organism and strain; the labelled basis; storage. Write the activity as a minimum and place the method appendix under document control.

Choose the routine identity check for each new lot: the organism statement, a protein comparison with a reference, or both. That decision keeps identity proactive. The grades page shows how carrier and form change those lines, and the specification glossary entry covers the vocabulary.

Five questions for the supplier

  1. What organism and strain stand behind the lot, and what CAS number does the certificate carry?
  2. What does the U/g mean in your assay: maltose concentration, pH, temperature and glucose detection?
  3. What activity and protein results did this lot produce, and what is the ratio between them?
  4. What is the glucose blank, and how was it subtracted?
  5. Which document ties the pack to its lot, and would you agree to a joint re-test of the retained sample?

Five written answers give a buyer an audit trail. An answer to the second alone gives a number: easy to issue, hard to check. Catalog figures sit on the maltase product page; lot tests on the COA page; method families under methods; the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation