06 Identity & adulteration

How we prove a lysozyme lot is lysozyme hydrochloride

Technical document 06 · Reviewed 2026-11-19 · Lysozyme

On this page
  1. The four layers of identity
  2. The protein and chloride ratios
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A lysozyme hydrochloride lot is the named material when four lines agree: the document names the enzyme and the salt form, the turbidimetric assay gives the declared activity under the stated conditions, the protein and chloride figures fit the hydrochloride, and the lot code ties the powder to the certificate. The activity alone cannot separate a genuine lot from a dilution, a free-base preparation or a different protein. Each line answers a different question, and a weakness in one leaves a gap the others cannot fill.

In one line

Identity is the agreement between the activity assay, the protein figure, the chloride content and the lot code, not the activity number alone.

The four layers of identity

The first layer is the document: the name, the CAS number, the source and the salt form. The second is the activity, measured by an assay whose substrate, temperature, pH and detection principle are written down. The third is the composition of the powder around the enzyme: how much protein it carries and whether chloride is present. The fourth is traceability, because a correct certificate attached to a different drum is still the wrong document for the delivery.

Four layers of lysozyme hydrochloride identity
LayerQuestionTestWhat it proves
DocumentIs the enzyme and salt form named?Name, CAS number, sourcePaperwork only
ActivityDoes the powder lyse the substrate at the declared rate?Turbidimetric assay on MicrococcusThe enzyme action, under one method
CompositionIs it the hydrochloride, and is it diluted?Protein, chloride, loss on dryingThe salt form and the concentration
TraceabilityDoes the certificate belong to this pack?Lot code on pack, certificate and retained sampleThe link between paper and powder

The protein and chloride ratios

The activity figure becomes a concentration check when it is divided by protein. Specific activity, in U/mg protein, separates a genuine concentrate from a powder extended with maltodextrin or glucose: dilution lowers both the activity per gram of powder and the protein per gram, so the ratio holds while the absolute figures fall. Protein is read by ultraviolet absorbance with a maximum at 281 nm and a minimum at 252 nm, or by a colorimetric assay against a standard. The certificate should name the method, because the two do not give the same denominator.

The salt form has its own ratio. The hydrochloride carries chloride as the counter-ion; a free-base preparation does not. Chloride by ion chromatography or titration therefore answers a question the activity assay cannot: two powders can both lyse Micrococcus at 20,000 U/mg and differ in whether the label name “hydrochloride” is true. The EU additive specification also sets a protein-content gate, not less than 950 mg/g on the anhydrous basis, which a U/mg figure alone does not demonstrate.

Neither ratio is a purity figure in the mineral sense. A lysozyme preparation is a protein powder with residual source proteins and possibly a carrier; the useful question is whether the activity, the protein and the chloride are consistent with the specification, not whether the powder is 100% enzyme.

X-ray diffraction and the solid state

X-ray diffraction answers a narrow question: is the solid crystalline, and does its pattern match a reference? Lysozyme is a protein that can be crystallised, so a diffraction pattern can distinguish a crystalline preparation from an amorphous dilution, and it can compare lots from two sources. It can also identify a crystalline carrier such as sodium chloride or a sugar in a blend.

It is not a routine release test for this product, and it is not a purity assay. A certificate that reports only “XRD conforms” without the pattern, the reference and the detection limit has added little. Ask for the reference diffractogram and the limit of detection before reading a match statement. For a disputed lot, XRD plus activity plus protein plus chloride is stronger than any one of them, but the activity assay remains the primary identity test for an enzyme.

What adulteration looks like

Lysozyme hydrochloride substitutions and the signals
Adulterant or mismatchWhat it doesSignalTest
Maltodextrin or glucoseLowers activity and protein per gramBoth figures fall togetherActivity, protein, loss on drying
Egg white powderAdds other egg proteins and lowers activity per gramProtein pattern differs; activity lowSDS-PAGE, activity, protein
Free base instead of hydrochlorideChanges the salt, mass and solution pHChloride absent or lowChloride by ion chromatography
Hydrolysed lysozymeDifferent ingredient; little or no enzyme activityActivity low despite proteinActivity, peptide pattern
Different lysozyme sourceSame enzyme name, different sourceSource statement or pattern differsSource-specific ELISA, protein pattern
Mislabelled lotCertificate belongs to another packLot code mismatchPack, certificate and retained sample

Colour and appearance are the weakest signals. White to off-white covers a wide range, and a dilution can look the same as a concentrate. The stronger signals are the activity-to-protein ratio, the chloride figure and the protein pattern. A certificate that reports appearance and activity but not the composition around the enzyme has left the most likely substitution untested.

How to write identity into the specification

  • “Lysozyme hydrochloride, CAS 9001-63-2, enzyme name muramidase, source declared on the certificate.”
  • “Activity ≥20,000 U/mg by the turbidimetric Micrococcus assay, with the unit definition and assay conditions stated.”
  • “Protein and specific activity reported; chloride reported where the hydrochloride form is claimed.”
  • “Loss on drying ≤5.0%; particle size ≥95% through 40 mesh.”
  • “Identity by activity assay and IR; SDS-PAGE pattern against a reference lot on request.”
  • “Egg allergen statement and source statement attached to the lot.”
  • “Destination market and salt form confirmed before the order.”

Five questions for the supplier

  1. Which salt form is this lot, and which CAS number and source are on the certificate?
  2. What is the exact unit definition, and what substrate, temperature and pH produced the U/mg figure?
  3. What are the protein and chloride results for this lot, and which methods were used?
  4. Can you provide the activity chromatogram or assay worksheet and the SDS-PAGE pattern, not only the final number?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single activity percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the activity and physical options; the salt comparison covers the label consequences; the methods library explains the analytical vocabulary; and the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation