06 Identity & adulteration

How we prove a lipase lot has the declared activity

Technical document 06 · Reviewed 2026-11-19 · Lipase

On this page
  1. Four layers of identity
  2. What the LU means
  3. The activity assay
  4. Protein and specific activity
  5. The activity-to-protein ratio
  6. XRD, and why lipase powder is not identified by it
  7. The adulteration routes
  8. How to write the specification
  9. Five questions for a lipase supplier

An enzyme has no crystal form or melting point to identify it by. Identity rests on the source and production record, the activity under a defined assay, the protein profile, and the absence of undeclared activity. A lipase figure alone is a rate, not an identity; unit and method must travel with it.

In one line

Activity is the identity test for an enzyme, and it only means something when the unit, the substrate and the method travel with the number.

Four layers of identity

Identity evidence for a lipase lot
LayerEvidenceWhat it catches
Source and production recordSpecies, strain, fermentation and recovery record, carrierA different organism or a mislabelled source
ActivityLU/g by the declared method, with substrate, pH and temperatureDilution, inactive material and method drift
ProteinTotal protein, specific activity and SDS-PAGE profileCarrier loading and a foreign protein
Adulteration screenSide activities, loss on drying, ash and microbiologySpiking with another enzyme, water or salt

The layers are not alternatives: a source record without activity is a label, and an activity result without a source could belong to any lipase.

What the LU means

One LU is the amount of enzyme that releases one micromole of titratable butyric acid per minute from a tributyrin emulsion at pH 7.0 and 30 °C. The unit describes a rate under named conditions, not a mass and not a purity. A 100,000 LU/g powder therefore carries 100 LU per milligram, carrier and fermentation solids included.

“LU” is not one international definition. The tributyrin assay is the common food-enzyme convention, but a supplier can define its own unit on another substrate or pH. The certificate has to print the conditions and the specification repeat them; “100,000 LU/g” alone is a number without a definition. The LU versus FIP page sets out the alternative.

The activity assay

The assay is a titration. A tributyrin emulsion is prepared at pH 7.0 and held at 30 °C; the enzyme is added, and the butyric acid released is titrated with sodium hydroxide to keep the pH constant. Base addition over the measured interval gives micromoles of acid per minute, divided by sample weight for LU/g.

The details decide the result. The emulsion has to be uniform, because lipase acts at the oil–water interface and a coarse emulsion presents less surface. The sample must be weighed accurately, because the activity is high. A blank, a standard preparation and at least two replicates belong in the record.

The assay is also the identity test, but only when the method transfers. A laboratory running olive oil at pH 9.0 and calling the result LU is not reproducing the certificate. If the customer's method differs, the supplier should report both results on the same lot, not convert one into the other.

Protein and specific activity

Total protein is measured by Bradford, Biuret or Kjeldahl, and specific activity is activity divided by protein mass, in LU per milligram. It separates a concentrate from a dilution: two preparations at 100,000 LU/g can carry different protein amounts, and less protein per unit of activity means a more purified material.

Candida rugosa lipase is a glycosylated protein of about 60 kDa, and the species produces several isoforms. An SDS-PAGE profile therefore shows a band or a small group of bands, not a single clean line; it is a consistency check, not a fingerprint. A different pattern is a different material.

The activity-to-protein ratio

Specific activity is LU per milligram of protein, calculated from the same lot as the activity result. It separates a concentrate from a dilution: a powder cut with carrier loses LU/g and protein together, so the ratio holds, while a heat-damaged lot keeps its protein and loses activity, so the ratio falls. It is a consistency check, not a purity percentage, because the protein method counts fungal proteins and any protein carrier alike. Within one grade and supplier it should sit in a stable band; the protein method belongs beside it.

XRD, and why lipase powder is not identified by it

Lipase powder is amorphous, and its X-ray diffractogram is a broad halo with no reflections belonging to the enzyme. XRD cannot distinguish Candida rugosa lipase from another lipase, confirm the strain or measure LU. Sharp peaks come from a crystalline carrier, a salt or a mineral contaminant; they describe the formulation, not the protein. Protein crystallography needs a single purified crystal, not a production lot.

The identity set here is the tributyrin assay with its conditions, total protein and specific activity, and an SDS-PAGE profile showing the expected band group near 60 kDa against a reference lot.

The adulteration routes

Lipase adulteration · what changes and what to check
RouteWhat changesCheck
Dilution with carrierActivity per gram falls; protein and specific activity fall; ash or moisture may riseActivity, protein, carrier and mass balance
Another lipase sourceActivity passes; protein pattern and source record differSDS-PAGE, specific activity, strain audit
Spent or inactivated enzymeProtein present, activity low; the powder may look normalActivity against protein, plus a fresh standard
Added side activitiesProtease or amylase appears; the declared lipase may still passSide-activity panel on the same sample
Water or saltLoss on drying or ash rises; activity per gram fallsLoss on drying, ash and the activity basis

None of these routes needs a sophisticated forgery. Dilution is the simplest and the easiest to detect if the specification asks for protein and specific activity beside the activity. Source substitution is harder, because the assay cannot tell one lipase from another; the protein pattern and production record catch it.

How to write the specification

Specification fields for a lipase lot
FieldWhat to write
IdentityLipase (triacylglycerol lipase, EC 3.1.1.3; CAS 9001-62-1) from Candida rugosa
Activity≥100,000 LU/g
Unit definition1 LU = 1 µmol titratable butyric acid per minute from tributyrin at pH 7.0 and 30 °C
BasisAs-is; loss on drying ≤8.0% reported beside the activity
ProteinTotal protein and specific activity (LU/mg protein) reported
SourceSpecies and strain recorded; organism absent from the final preparation
CarrierIdentity and inclusion declared on the COA
Side activitiesProtease and amylase screened and reported
End of shelf lifeMinimum activity at the stated storage condition, not only release

A specification written this way can be checked by a second laboratory and audited by a second customer; a line reading only “lipase 100,000 LU/g” cannot.

Five questions for a lipase supplier

  1. What is the exact unit definition and assay: substrate, pH, temperature, reaction time, detection and standard?
  2. What are the lot's activity, protein and specific activity, and on what basis is activity reported?
  3. Which species and strain produced the lot, and how is the production organism removed?
  4. What carrier or diluent is added, and which side activities are controlled and reported?
  5. What activity remains after the customer's process step, and what stability data support the shelf life?

The answers should match certificate and specification. The catalog position is on the lipase product page, the release lines on the COA page, the grade options on the grade page, and the workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation