03 Stability

Keratinase loses activity to heat and moisture; the process sets the shelf life

Technical document 03 · Reviewed 2026-11-20 · Keratinase

On this page
  1. The powder: moisture is the first enemy
  2. The solution: a short working life
  3. What drives the loss
  4. A stability protocol for the preparation
  5. The matrix changes the answer
  6. How the shelf life is set

Keratinase is a protein, so its activity falls when the powder absorbs water or a solution is held warm. The sealed powder is the more durable format; a liquid has a short working life and needs its own data. The pack and the process, not the certificate, set the shelf life.

In one line

Heat and moisture destroy keratinase activity, and the pack, the feed process and the storage condition decide how much survives.

The powder: moisture is the first enemy

The specification allows up to 8.0% loss on drying at release. That figure is a gate, not a reserve for storage. Once a pouch is open, the powder equilibrates with the room; in a damp filling hall it can gain moisture within a shift. Because the assay is reported on the powder as weighed, water uptake lowers the activity per gram, and caking follows. Keep the pack closed between weighings, store it away from hot spots, and let a cold container reach room temperature before opening it, or condensation will form on the powder.

Heat speeds the loss even when moisture is low. A sealed pack in a controlled store is not the same material as a drum left in a loading bay. Warm, damp protein unfolds and aggregates, and the activity does not return on cooling.

The solution: a short working life

The powder dissolves in water to a clear to slightly turbid solution. In solution, the enzyme is exposed to autolysis, microbial growth and pH drift, and activity falls faster than in the dry pack. Mix only the concentration the process needs, hold it for a validated time, and discard the remainder rather than storing it overnight. A preservative does not replace a hold-time study.

Stabilisers can lengthen the life of a liquid, but the effect depends on the enzyme, the pH and the other ingredients. A polyol or a salt that protects one preparation may inhibit another. A stabilised liquid is its own specification, with activity measured at release and at the end of the hold.

What drives the loss

Factors that move keratinase activity during storage and use
FactorWhat it doesControl
HeatUnfolds the protein; the rate rises with temperatureCool store; keep the process inside the validated window
MoistureRaises loss on drying; promotes aggregation and cakingSealed pouch; dry store; desiccant where the climate needs it
pHMoves the enzyme away from its working rangeBuffer the solution; check the pH of the process stream
Metal ionsSome inhibit, some activate; the effect is preparation-specificLimit iron and copper contact; test the process water
Shear and foamDenatures protein at air–liquid interfacesLow-shear mixing; avoid over-agitation
Microbial loadGrows in a dilute solution and consumes the preparationHygienic handling; validated hold; filtration where suitable
Reducing agentsCleave disulfide bonds and change the rate on keratinControl as a process additive, not a routine stabiliser

The factors combine. A warm, humid store is worse than either condition alone, and a warm solution at the wrong pH loses activity faster than a cold one at the right pH. The useful question is not whether keratinase is stable in general, but how much activity remains in this pack, at this condition, after this process.

A stability protocol for the preparation

Choose the pack and the climate, then set the time points. A warehouse study usually runs at 25 °C/60% relative humidity, with an intermediate arm at 30 °C/65%; an accelerated arm at 40 °C/75% tests the barrier. At each point, measure activity, moisture, appearance and microbial count, and keep the raw numbers. A summary that says “stable” without results is not evidence.

For a feed or technical process, add a process arm. The conditioner, dryer or extruder imposes a heat and moisture load that no cabinet reproduces. Assay before and after the step in the real matrix; that loss, not a generic overage, sets the addition rate.

The matrix changes the answer

A mash, a mineral premix and a post-pellet liquid are three different environments. The mash carries water and its own enzyme activity; the premix brings salts that can shift pH or inhibit; the liquid brings a carrier, a preservative and a hold time. A blend with other enzymes adds further interactions, and the blend's stability is measured on the blend.

Pelleting is the usual stress in feed. The conditioner adds heat and water, and unprotected protein loses activity with temperature and dwell. Adding the enzyme after the press avoids the conditioner but creates a liquid hold; a granulated grade may retain more through the press. The choice is made on activity measured after the step.

How the shelf life is set

Keratinase has no single shelf life that fits every pack. The retest period is assigned to a pack and a storage condition, and the data file for that combination has to support it. A figure that omits the pack, the climate and the tests is not a shelf life.

Before extending the period, run the assay again on the retained sample. A bulk result does not carry over to a repacked container. The product page lists the packs; the MOQ page sets out the packs and the dispatch window; the identity page covers the assay; the neutral protease pages show the same logic for another enzyme; the methods index leads to the assay notes; the quality page describes release and retest.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation