03 Stability

Catalase stability: heat, moisture and the pack

Technical document 03 · Reviewed 2026-11-19 · Catalase

On this page
  1. The powder: moisture, heat and the pack
  2. The solution: dilute, warm and unprotected is the worst case
  3. What drives the loss
  4. A stability protocol for the ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

Catalase is a protein, and what decays on storage is activity rather than mass: heat, moisture, alkaline pH, proteases and repeated freezing remove units while the powder can still look unchanged. A sealed powder at release moisture holds its activity longer than any solution, and a dilute solution at room temperature is the fastest way to lose it. The retest period comes from data on the pack being bought, not from the certificate.

In one line

The activity is the shelf life: heat, moisture, alkaline pH and dilution remove units long before the powder looks different.

The powder: moisture, heat and the pack

The catalog sets loss on drying at ≤8.0%. That figure is a gate at release, not an allowance for storage. Once the pouch is open, the powder pulls moisture from the air, the measured loss on drying climbs and the units fall away; the powder can stay white and free-flowing while its activity is going. A heat-sealed foil pouch is a barrier only while it is intact. After the first opening, move the remainder into a smaller opaque container, or finish it inside the in-use period agreed for the material.

Heat is the second driver, and it acts on the dry powder as well as on solutions. A warehouse at ambient temperature is not the same condition as a loading bay in summer, and a drum left in the sun can reach temperatures that cost activity at the surface. In the 25 kg drum the liner, not the board, is the moisture barrier: close it after sampling, mark the opening date on the label and keep the drum off a damp floor.

Cold storage helps, with one practical rule: let the sealed pack equilibrate to room temperature before opening it. Otherwise condensation forms on the powder, and the water arrives exactly where the specification tried to keep it out. A desiccant absorbs what gets past the closure; it cannot stop the leak, so fix the seal first.

The solution: dilute, warm and unprotected is the worst case

Catalase dissolves in water to a clear to slightly turbid solution. In solution the enzyme is diluted, and catalase is a tetramer: at low concentration the subunits can dissociate and the activity falls, a loss that is not caused by heat and is not reversed by concentrating the sample afterwards. Albumin, glycerol or a higher ionic strength can slow that dissociation, but the practical answer is to keep the solution concentrated, cold and short-lived.

Several common preservatives are the wrong choice for this enzyme. Azide and cyanide bind the heme iron and inhibit catalase, so a preservative screen has to include an activity check, not only a microbial one. Hydrogen peroxide is the substrate, but a large excess inhibits and eventually inactivates the enzyme, which is why both the assay and any process that uses peroxide need a defined concentration and contact time. Freeze-thaw cycles concentrate the protein and damage the tetramer; aliquot before freezing and thaw once.

The solution pH should sit near neutral. Alkaline conditions and strongly acid conditions both cost activity, and the effect is faster at higher temperature. A clear solution in a warm room is not a stable hold, and a powder stability result does not describe it.

What drives the loss

Factors that move catalase activity during storage
FactorWhat it doesControl
HeatUnfolding and aggregation; activity fallsCool store; control process heat
MoistureRaises loss on drying and water activity; promotes aggregationSealed pouch; dry store; desiccant
pHActivity is highest near neutral; alkaline solutions lose unitsBuffer near neutral; check the matrix
PeroxideExcess substrate inhibits and inactivates the enzymeDefine the concentration and contact time
Freeze-thawConcentration and ice damage the tetramerAliquot; freeze once
Proteases and microbesCleavage of the protein; growth in a wet powder or solutionMicro limits; compatible preservative

Heat and moisture rarely act alone: a warm, damp store multiplies the two, and a dilute alkaline solution adds pH and dilution to the same test. The question that matters is how many units survive in this pack, under this condition, for this long.

A stability protocol for the ingredient

The protocol should fix the pack, the condition, the time points and the panel of tests. A common design keeps one lot at 25 °C/60% relative humidity as the long-term arm, a second at 30 °C/65% for intermediate coverage and a third at 40 °C/75% as the accelerated arm. If the process includes a solution hold or a freeze-thaw, add an arm for each; a dry incubator will never reveal those failures.

Activity is the primary endpoint, and it has to be run with the release method and the same conditions. Loss on drying, appearance, IR identity and microbiology belong at each point too. The report should give the measured values and the assay's repeatability, not a final verdict, and it should name the pack and the production family. Data from a different pack does not support the pack in the quotation.

The finished formula changes the answer

Capsules and tablets keep water activity low, yet the excipients and the shell still hold moisture, and a wet granulation brings water and heat together. Measure activity after compression as well as after storage, not only on the bulk powder. A blend adds segregation when particle sizes differ, and a protease in the same blend can digest catalase on the shelf. A stick pack lives or dies by its seal: a pinhole is a failure, so inspect the strip as well as the powder inside it.

In a liquid, pH, preservative, heat and time act together. Bulk powder data is the starting point, not the answer, and any overage is a formulation and labelling choice. An overage does not rescue a pack that leaks moisture.

How the shelf life is set

Catalase has no universal shelf-life figure. The retest period is written against a named pack and storage condition, and the stability file is the evidence behind it. A number quoted without the pack, the condition and the panel cannot be checked, and a bulk figure does not transfer to a repacked container. At the end of the period, re-assay the retained sample before extending use.

Standard packs are listed on the catalase hub; the COA page sets out the release tests, and the MOQ page the pack and lead time. The methods library describes the activity assay, and the quality page covers the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation