02 Grade comparison

1,200 or 2,400 GDU/g: choosing a bromelain grade

Technical document 02 · Reviewed 2026-11-19 · Bromelain

On this page
  1. Activity is a concentration, not a strength rating
  2. The two grades side by side
  3. Mesh, flow and dust
  4. What each dosage form can carry
  5. What changes when you switch
  6. When a different grade is the wrong answer

A 2,400 GDU/g grade and a 1,200 GDU/g grade can be the same pineapple enzyme at two concentrations, because the lower grade is normally the higher preparation diluted with a food-grade carrier. The choice is not about which number is better; it is about how much activity a serving needs and how much powder the dosage form can carry. The label, the capsule size and the assay target all follow from that decision.

In one line

The grade is chosen by the activity a serving needs, not by the number on the first quotation; switching grades changes the powder mass, the carrier load and the label.

Activity is a concentration, not a strength rating

GDU/g is activity per gram of powder. One kilogram of the 2,400 grade carries 2.4 million GDU; one kilogram of the 1,200 grade carries 1.2 million. To deliver a fixed number of GDU, the lower grade needs twice the powder mass. That is the whole arithmetic, and it applies whether the grade difference comes from dilution, from a different extraction cut or from a different drying yield.

The catalog grade here is ≥2,400 GDU/g, with lower-activity dilution available on request. A diluted grade is a legitimate product when the certificate names the carrier and the activity is measured on the blend, not calculated from the concentrate. A blend that is merely assumed to be 1,200 GDU/g because it was mixed one-to-one is not a specification; it is an estimate.

The two grades side by side

1,200 and 2,400 GDU/g · activity and mass
Property1,200 GDU/g2,400 GDU/g
Activity per kilogram1.2 million GDU2.4 million GDU
Powder for 3,000 GDU2.5 g1.25 g
Powder for 12,000 GDU10 g5 g
Carrier load at equal activityHigherLower
Typical fitSticks, blends, tabletsCapsules, low-mass sticks

The table is arithmetic, not a batch result. A 500 mg capsule filled with the 2,400 grade carries at most 1,200 GDU; the same capsule filled with the 1,200 grade carries at most 600 GDU. Neither capsule can reach 3,000 GDU without a larger fill or a stronger grade, which is why capsule formats usually begin with the higher activity and stick packs can use either.

Mesh, flow and dust

The catalog grade is sold at ≥95% through 40 mesh, and a diluted grade should carry the same sieve specification. Both are fine powders with the flow and dusting that come with that mesh. The difference is how much powder carries a given activity: a formula built on the 1,200 grade handles twice the mass for the same GDU, so the blender, the filler and the pack see more material. That can be an advantage in a stick pack, where mass helps the sachet feel substantial, and a problem in a capsule, where mass is capped by the shell.

Granulated forms are available on request and change the flow without changing the declared activity. Do not use a grade change to fix a flow problem; a granulation or a mesh change is the direct fix, and it keeps the label arithmetic intact. A carrier introduced by dilution can also change hygroscopicity and caking, so the pack and the storage statement should be checked after the switch.

What each dosage form can carry

A two-piece capsule holds roughly 300–800 mg of powder depending on size and fill. At 2,400 GDU/g that is 720–1,920 GDU per capsule; at 1,200 GDU/g it is 360–960 GDU. A 5 g stick pack at 2,400 GDU/g can carry up to 12,000 GDU, and the same stick at 1,200 GDU/g carries up to 6,000 GDU. Tablets add a compression step: the activity in the tablet is what survives the press, not what was in the blend.

The label arithmetic is simple but easy to get wrong. Write the activity per gram and the mass per serving, then multiply. “Bromelain 2,400 GDU/g, 500 mg” supplies 1,200 GDU per serving. “Bromelain 1,200 GDU/g, 500 mg” supplies 600 GDU. If the label declares only “Bromelain 500 mg”, the reader cannot tell which grade was used, and the two products are not interchangeable at the same mass.

Uniformity is the second dosage-form question. A low-dose, high-activity grade is a small fraction of the blend, so segregation matters more; a high-mass, lower-activity grade is easier to distribute but brings more carrier into the formula. Whichever way the formula moves, the blend study has to be repeated on the new grade.

What changes when you switch

  • The powder mass per serving, and therefore the capsule size or sachet fill.
  • The carrier load and the excipient declaration on the label.
  • The blend uniformity and the mixing time for the new particle mix.
  • The release activity target, because the grade defines the floor.
  • The label activity statement and the serving arithmetic.
  • The stability data, because more carrier can mean more moisture uptake.

Write the grade into the purchase order as an activity, not only as a grade name: “Bromelain from pineapple stem, ≥2,400 GDU/g by the gelatin method, as-is basis, carrier declared.” Then the certificate and the label speak the same language. If the grade is changed later, handle it as a formula change and re-run the blend, fill and stability checks rather than reprinting the label alone.

When a different grade is the wrong answer

A flow or caking complaint belongs to the mesh, the granulation or the pack, not to the activity grade. A potency complaint belongs to the assay method and the certificate, not to a higher grade bought to compensate. A label complaint belongs to the declaration, not to a new drum. The units themselves are a separate decision: GDU and FIP measure the same kind of activity on different substrates, and the unit comparison explains why the numbers are not interchangeable.

The catalog grade and its limits are on the bromelain product page. What the certificate reports for that grade is on the COA page; heat and moisture limits are on the stability page; the pack sizes and the 1 kg minimum are on the ordering page. The term itself is defined in the assay glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation