How we prove an acid protease lot has the declared activity
Four questions have to be answered before a powder can be called acid protease: what preparation is it, what rate does it show at acid pH, how much protein carries that rate, and which lot is in the pack. A certificate that answers only the rate has described one of the four. The pH-activity pair is the check that distinguishes an acid enzyme from a neutral one.
An acid protease lot is identified by its activity at acid pH, the protein behind that activity and the lot record, not by the number on the certificate alone.
The four identity layers
The layers are separate questions, and a supplier can answer the first with a name and the second with a number while leaving the third and fourth blank. Each answer belongs on the specification or the certificate, not in a covering email.
| Layer | Question | Evidence |
|---|---|---|
| Preparation | Is the name, CAS and source declared? | Specification, CAS 9025-49-4, organism and carrier |
| Catalytic behaviour | Is the rate acid-dependent? | U/g at pH 3 and pH 7, with the method |
| Protein basis | How much protein supports the rate? | Protein method and specific activity in U/mg |
| Traceability | Can the paper be tied to the pack? | Lot code, certificate and retained sample |
The preparation layer is not clerical. The organism and carrier determine which market file and which label apply, and a CAS number alone does not name the preparation.
Specific activity and the pH ratio
The protein basis is a ratio, not a separate purity claim. Divide activity by protein and the result is U/mg. A carrier reduces both numerator and denominator, so the ratio survives a dilution; heat reduces the numerator only, so the ratio falls. A stable U/g with a falling ratio is a warning that the powder contains more protein for the same activity — a different cut, an inactivated fraction or an undeclared carrier.
The acid signature is a second ratio: activity at pH 3 divided by activity at pH 7. For an acid protease the first should be large and the second small; a neutral protease reverses the pattern. Dilution does not change the sign of that ratio, and a blend of the two may pass the acid assay while carrying more neutral activity than the label allows. Run both assays on one sample, with the same substrate lot and detection.
What diffraction and infrared can and cannot say
X-ray diffraction is not the right identity method for an enzyme. A dried protein powder is amorphous; the scan shows a broad halo and no sharp reflections. The halo may help spot a crystalline carrier or a mineral contaminant, but it does not identify the protein or measure activity.
Infrared spectroscopy does better: the amide bands show that the sample is protein, and their shape carries some secondary-structure information. It still does not say which enzyme is present. That is why the catalog identification entry combines IR with the activity assay. Gel electrophoresis provides the missing comparison: run the lot beside a reference and read the band pattern, the main protease band and any extra bands.
Routes that can satisfy a weak test
| Route | What passes | What detects it |
|---|---|---|
| Bulking with a carrier | The blend still reaches the declared U/g | Carrier statement, mass balance, protein and specific activity |
| Neutral protease substituted | A general protease assay shows activity | pH 3 against pH 7, protein pattern, strain record |
| Activity destroyed by heat | Protein and colour remain | Both activity and specific activity drop |
| Free amino acids added | Folin colour reads high | Reagent blank and sample clean-up |
| Carrier changed without notice | Activity remains in specification | Carrier identity and composition statement |
| Different production strain | The generic name still applies | Strain declaration, origin record and protein pattern |
The free amino acid route exploits the detection chemistry. Folin-Ciocalteu reacts with tyrosine, tryptophan and reducing substances, so a spiked sample can read high without more enzyme; a blank and a clean-up remove the illusion. A silent carrier change is less dramatic but just as real: the activity stays in specification while the powder's flow, dust and label declaration change.
A specification that can be checked
- “Acid protease preparation, CAS 9025-49-4, ≥100,000 U/g; organism and strain declared.”
- “The U defined by the Folin-Ciocalteu assay at the stated acid pH; substrate, temperature, time and standard on the COA.”
- “Activity at pH 3 and pH 7 on one sample, or a full pH profile.”
- “Protein and specific activity, with the method named.”
- “As-is result; loss on drying ≤8.0%.”
- “IR compared with the reference; particle size ≥95% through 40 mesh.”
- “Carrier declared; no undeclared diluent or second protease.”
The carrier line is not optional. A dilution is legitimate when the carrier and the lower activity are both in the specification; it is not legitimate when the original U/g label is kept.
Five questions before qualification
- Which organism and strain were used, and where is the record held?
- What is the definition of one U here — substrate, acid pH, temperature, time, detection and standard?
- What are the activity, protein and specific activity of this lot?
- What activity do you measure at pH 3 and at pH 7 on the same sample?
- What carrier or second enzyme is present, and where is it declared?
Answers in writing to all five give a buyer a file to audit. An answer to the third alone gives a number that is easy to issue and hard to check. The product page lists the catalog values; the COA page shows where each figure belongs; the neutral protease page gives the other pH window; the alkaline protease page gives the third; the methods index covers the assay families; and the quality page describes release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation